Semester-wise study map
Eight semesters, every subject, 120 lessons and the matching lab experiments, in the order most electronics degrees teach them.
Universities differ in the order and names of subjects, so treat this as a guide to what to learn when. Check your own syllabus and lab manual, and use the lab section for your university's experiment list.
Semester 1
Circuit basics and measuring
Basic electrical and electronics
Voltage, current, resistance and the laws every later subject uses.
Lessons
- Voltage, Current & Resistance Beginner
- Ohm’s Law, Power & Heat Beginner
- Resistor Networks & Loading Beginner
- Reading and Choosing Resistors Beginner
- Kirchhoff's Laws Intermediate
Lab experiments
Workshop and measurement practice
Meters, breadboards, schematics and safe habits before you build.
Lessons
- Using a Multimeter Beginner
- Breadboards and Wiring Beginner
- Reading a Schematic Beginner
- Through-Hole Soldering That Lasts Intermediate
- Interpreting Sensor Data Beginner
- Power Safety for Makers Beginner
Lab experiments
Semester 2
Network analysis and first devices
Network analysis
Solve any linear circuit with theorems and see how it behaves in AC.
Lessons
- Thevenin Equivalents and Loading Intermediate
- Nodal Analysis and Circuit Simulation Advanced
- Signals: Frequency, Period and Duty Cycle Intermediate
- AC, RMS and Real Power Advanced
- Impedance, Reactance and Phase Advanced
Lab experiments
Passive components and transients
Capacitors and inductors store energy, and that is what makes filters and timing work.
Lessons
- Capacitors & Inductors Beginner
- Capacitor Types and Markings Beginner
- Real Components: Parasitics, ESR and Derating Advanced
- RC Filters and Time Constants Intermediate
- Transformers and Isolation Intermediate
Lab experiments
Electronic devices: the diode
The first semiconductor: rectifying, clamping and regulating.
Lessons
- Diodes, LEDs & Polarity Beginner
- Zener Diodes and Simple Voltage References Intermediate
- LEDs and Current Limiting Beginner
Lab experiments
Semester 3
Transistors and digital logic
Electronic devices and circuits
Use a transistor as a switch and as an amplifier, and bias it properly.
Lessons
- Using a Transistor as a Switch Beginner
- Transistors & MOSFET Switching Intermediate
- Constant-Current LED Drivers Advanced
- Decoupling and Bulk Capacitors Intermediate
Lab experiments
Digital electronics
Number systems, gates and the building blocks of every digital system.
Lessons
- Binary, Hex and Bits in Practice Beginner
- Logic Gates and Truth Tables Beginner
- Logic Levels: 5 V and 3.3 V Together Intermediate
- Flip-Flops, Debouncing and Counters Intermediate
- Shift Registers: More Pins from Three Intermediate
- Counters and Seven-Segment Displays Beginner
Lab experiments
- Verification of logic gates and universal gates
- Realising a Boolean function in SOP and POS forms
- Half adder and full adder
- Multiplexer (4:1 and 8:1) and realising a function with it
- Flip-flops: SR, JK, D and T
- Counters: asynchronous, synchronous and decade
- Shift registers (SISO, SIPO, ring and Johnson counters)
Semester 4
Op-amps, power and microcontrollers
Linear integrated circuits
Op-amps do the maths of analogue electronics: gain, sums, filters and oscillators.
Lessons
- Designing with Op-Amps Advanced
- Op-Amp Basics and Comparators Intermediate
- MOSFET Gate Drive and Switching Losses Advanced
Lab experiments
- Op-amp inverting and non-inverting amplifiers
- Op-amp adder (summing) and subtractor (difference) amplifiers
- Op-amp integrator and differentiator
- Schmitt trigger using an op-amp
- Instrumentation amplifier (three op-amp)
- Active low-pass, high-pass and band-pass filters
- RC phase-shift oscillator
- Wien bridge oscillator
- Hartley and Colpitts (LC) oscillators
- 555 timer as an astable multivibrator
- 555 timer as a monostable multivibrator
- 4-bit R-2R ladder D/A converter
Power supplies
Turn a battery or mains adapter into clean, safe rails.
Lessons
- Batteries: Voltage, Capacity and Runtime Beginner
- Linear Regulators and Heat Beginner
- Buck and Boost Converters Intermediate
- Power Budgets and Thermal Design Advanced
Lab experiments
Microcontrollers
Read inputs, drive outputs and measure the world with code.
Lessons
- Arduino and ESP32 Basics Beginner
- Getting Started with the ESP32 Beginner
- Digital Inputs and Outputs Beginner
- PWM Timing & Actuator Interfaces Intermediate
- ADC Measurement & Reference Error Intermediate
- Interrupts, Timers and FreeRTOS on ESP32 Advanced
Lab experiments
Semester 5
Sensors, communication and power electronics
Sensors and instrumentation
Turn temperature, motion and distance into numbers you can trust.
Lessons
- Sensor Interfaces Beginner
- Temperature and Humidity Sensors Compared Beginner
- Distance and Motion Sensors Intermediate
- Calibrating Sensors and Estimating Uncertainty Advanced
- Accurate ADC Readings: Calibration and Filtering Advanced
- Measuring Mains Current Safely with a CT Advanced
Lab experiments
Communication protocols
How chips and boards talk to each other, wired and wireless.
Lessons
- Serial Communication Basics Beginner
- SPI, UART & Interface Trade-offs Intermediate
- I²C Addressing & Shared Buses Intermediate
- Wi-Fi, Bluetooth & Radio Constraints Intermediate
- Bluetooth Low Energy: GATT Services Advanced
- RS-485, Modbus and CAN Advanced
Power electronics
Switching converters, gate drive and keeping parts cool.
Lessons
- Designing a Buck Converter Stage Advanced
- Inductors, LC Filters and Noise Advanced
- MOSFET Gate Drive and Switching Losses Advanced
- Li-ion Charging and Power Safety Intermediate
- Solar Charging a Battery Project Intermediate
Semester 6
Embedded systems, IoT and PCB design
Embedded systems
Firmware that is debuggable, low power and updatable in the field.
Lessons
- Firmware Build, Logs & Fault Isolation Intermediate
- Interrupts, Timers and FreeRTOS on ESP32 Advanced
- Battery Life and Low-Power Design Advanced
- Bootloaders and Over-the-Air Updates Advanced
- Choosing Exact Boards & Modules Intermediate
- Embedded Displays & User Interfaces Intermediate
Internet of Things
Connect devices, send data reliably and keep it secure.
Lessons
- Connected Embedded Devices Beginner
- Connecting an ESP32 to Wi-Fi Beginner
- MQTT Basics: Publish and Subscribe Beginner
- Devices and Web APIs: HTTP, REST and JSON Intermediate
- Measurement Logging & Calibration Intermediate
- Your First Sensor Chart and IoT Dashboard Beginner
- Security, Privacy & Safe Remote Control Advanced
PCB design and hardware
Take a schematic to a manufactured, solderable board.
Lessons
- Reading Schematics & Design Evidence Intermediate
- Your First PCB in KiCad Intermediate
- PCB Layout Rules That Work Advanced
- PCB Power Distribution and Grounding Advanced
- Design for Manufacture and Gerber Checks Advanced
- SMD Soldering and Rework Advanced
Embedded Linux
Use a Raspberry Pi where a full operating system is worth having.
Lessons
- Setting Up a Raspberry Pi Beginner
- Linux Command Line for Raspberry Pi Beginner
- Raspberry Pi GPIO with Python Beginner
- I2C Sensors on a Raspberry Pi Intermediate
- A Web Dashboard on the Pi with Flask Intermediate
- Pairing a Pi with a Pico for Real-Time Control Advanced
- Running Pi Projects as Services Advanced
Semester 7
Edge AI, control and test
Embedded AI and vision
Run a model on a microcontroller, Pi or Jetson and know what it costs.
Lessons
- What Is Edge AI and TinyML? Beginner
- Train a Gesture Model for a Microcontroller Intermediate
- Quantising and Deploying TinyML Models Advanced
- Raspberry Pi Camera with Picamera2 Intermediate
- On-Camera AI with the Raspberry Pi AI Camera Advanced
- What a Jetson Is and When to Use One Beginner
- First Boot on a Jetson Orin Nano Beginner
- Jetson GPIO and Sensors with Python Beginner
- Camera Pipelines on Jetson Intermediate
- Object Detection with Pretrained Models on Jetson Intermediate
- Training a Custom Detector for Jetson Intermediate
- Optimising Models with TensorRT Advanced
- Jetson Power Modes, Heat and Field Deployment Advanced
- Multi-Camera Video Analytics with DeepStream Advanced
Actuators and control
Drive motors safely and fuse sensors for stable motion.
Lessons
- Motor Power and Drivers Intermediate
- Actuators, Motor Drivers & Protection Intermediate
- Relays and Servos for Beginners Beginner
- Stepper Motors and Motion Control Advanced
- IMUs and Sensor Fusion Advanced
- State Machines Advanced
Advanced digital design
Describe hardware in code and keep it correct at speed.
Lessons
- From Logic Gates to FPGAs and Verilog Advanced
- Timing, Setup and Hold, and Metastability Advanced
- State Machines Advanced
Test and measurement
See what the circuit is really doing and find faults quickly.
Lessons
- Using an Oscilloscope Intermediate
- Using a Logic Analyser Intermediate
- Measuring Fast Signals and Bus Problems Advanced
- Systematic Fault Finding Advanced
Semester 8
Final-year project
Plan and build the project
Choose a scope you can finish, build it, and make it look finished.
Lessons
- Planning a Prototype Beginner
- Designing an Enclosure That Fits Intermediate
- 3D Printing Basics for Electronics Beginner
- Power Safety for Makers Beginner
Make it reliable
Examiners and users both notice when a device fails after an hour.
Lessons
- Reliable Telemetry & Offline Recovery Advanced
- Reliable MQTT: QoS, Retained, LWT and Security Advanced
- Systematic Troubleshooting Beginner
- Systematic Fault Finding Advanced
Common questions
Does this follow my university's syllabus?
Not exactly. It follows the order most electronics degrees use, but universities name and order subjects differently. Use it as a guide and check your own syllabus and lab manual.
Is everything on the semester map free?
Every lesson's explanation and every lab experiment page is free to read. Worked examples, hands-on tasks and quizzes for Intermediate and Advanced lessons come with Maker and Pro plans.
Where do I find my university's lab list?
The lab section lists the experiments checked against published university lab lists, with theory, procedure, viva questions and virtual readings.
