Learn / Basics / Voltage, current and resistance

Voltage, Current & Resistance

ReviewedBeginnerFreeAbout 5 min
Vout = 2.5 V
In short

Voltage, Current & Resistance: the short answer

Voltage is electrical potential difference; current is charge flow; resistance opposes that flow. Ohm’s law V = I × R helps estimate current in a simple resistor path. Example: About 5 mA. Measure it with the meter in series and expect 4.8 to 5.2 mA with a 5 % resistor.

Level
Beginner
Time
About 5 min
Topic
Basics
You will learn to

Tell voltage, current and resistance apart, and estimate current with Ohm's law.

Voltage is electrical potential difference; current is charge flow; resistance opposes that flow. Ohm’s law V = I × R helps estimate current in a simple resistor path.

Consider a closed resistive path and identify where a voltage is measured. Voltage is taken between two points; current is measured through a branch. Increasing resistance at constant voltage reduces the ideal current, but real sources may have internal resistance and protection circuits.

Worked example: place 2.2 kΩ across an ideal 3.3 V supply; expected current is 1.5 mA. An ammeter must be inserted in series with appropriate range and protection, never casually across a battery as though measuring voltage.

A picture that works: water in pipes

Think of voltage as pressure, current as the amount of water flowing past a point each second, and resistance as a narrow section of pipe. More pressure pushes more water through the same pipe. A narrower pipe lets less through at the same pressure. That is Ohm's law in words: current = voltage ÷ resistance.

The picture breaks down in places (electrons are not water, and a wire does not leak when you cut it), but it gets the three quantities right, and that is what matters when you first start sizing parts.

Voltage is always between two points

A voltage is a difference. When someone says a pin is at 3.3 V, they mean 3.3 V above ground, the point the circuit treats as zero. That is why a multimeter has two leads: the black one sits on the reference and the red one on the point you want to know about.

This also explains why touching one wire of a car battery is harmless, and why a bird can sit on a power line: no current flows unless there is a path between two points at different voltages.

Current is the same all the way round a single loop

In a simple loop of battery, switch, resistor and LED, the current leaving the battery is exactly the current coming back. Nothing is used up on the way; what changes is the voltage, which drops a little across each part. Beginners often expect the LED to get "less current" because it comes after the resistor. It doesn't: the order of parts in a single loop does not change the current.

Current is measured through a wire, so the meter has to become part of the loop. That is why measuring current means breaking the circuit and putting the meter in the gap.

Units you will meet every day

Microcontroller circuits live in milliamps (mA, thousandths of an amp) and kilohms (kΩ, thousands of ohms). Handy shortcut: volts ÷ kilohms gives milliamps directly. 5 V across 1 kΩ is 5 mA; 3.3 V across 10 kΩ is 0.33 mA.

An ESP32 pin should source no more than about 20 mA for a long life, an Arduino Uno pin about 20 mA (40 mA is the absolute limit), and a USB 2.0 port gives 500 mA. Knowing these few numbers lets you spot a bad design before you build it.

Real sources are not ideal

Ohm's law assumes the supply holds its voltage whatever you connect. Real batteries have internal resistance, so their voltage sags as current rises. A fresh 9 V battery may read 9.4 V with nothing connected and drop below 8 V while driving a motor. Bench supplies and USB ports have current limits that pull the voltage down when you ask for too much.

So the calculation gives you the expected value; the multimeter tells you what really happens. The gap between the two is where most of the learning is.

Common mistakes
  • Putting the meter across a battery while it is set to measure current. In current mode the meter is almost a short circuit, so this blows its fuse or heats the battery.
  • Mixing units: 5 V ÷ 1 kΩ is 5 mA, not 5 A. Write the unit with every number until it becomes a habit.
  • Forgetting a common ground. Two boards that talk to each other must share ground, or the voltages they send mean nothing to each other.
Key formulas
V = I × R
V in volts, I in amps, R in ohms
Try it: Ohm's law, live

Current against voltage

0 A20 mA40 mA0 V5 V10 VVoltage22.7 mA

For a resistor, current rises in a straight line with voltage. A bigger resistor gives a shallower line.

I = V ÷ R = 22.7 mA, P = V × I = 114 mW

Current against voltage. The slope is 1 ÷ R.

Work it with your own numbers: Ohm's law

Worked example

How much current does a 1 kΩ resistor take from USB 5 V?

  1. Known: V = 5 V, R = 1 kΩ = 1000 Ω.
  2. Ohm's law: I = V ÷ R = 5 ÷ 1000 = 0.005 A.
  3. Convert: 0.005 A × 1000 = 5 mA.
  4. Check: a USB port gives at least 500 mA, so 5 mA is tiny.

Result. About 5 mA. Measure it with the meter in series and expect 4.8 to 5.2 mA with a 5 % resistor.

Try it

Given a 5 V source and a 1 kΩ ideal resistor, estimate the current: 5 mA. Check units and battery limitations.

Check yourself

3 quick questions

  1. A 1 kΩ resistor is connected across a 5 V supply. What current flows?

  2. How do you connect a multimeter to measure current?

  3. The voltage stays the same and you double the resistance. What happens to the current?

Common questions

What will I learn in "Voltage, Current & Resistance"?

Tell voltage, current and resistance apart, and estimate current with Ohm's law.

How much current does a 1 kΩ resistor take from USB 5 V?

Known: V = 5 V, R = 1 kΩ = 1000 Ω. Ohm's law: I = V ÷ R = 5 ÷ 1000 = 0.005 A. Convert: 0.005 A × 1000 = 5 mA. Check: a USB port gives at least 500 mA, so 5 mA is tiny. About 5 mA. Measure it with the meter in series and expect 4.8 to 5.2 mA with a 5 % resistor.

A 1 kΩ resistor is connected across a 5 V supply. What current flows?

5 mA. I = V ÷ R = 5 V ÷ 1000 Ω = 0.005 A, which is 5 mA.

How do you connect a multimeter to measure current?

In series, so the current flows through the meter. Current is measured through a branch, so the meter goes in series. Across a battery on the current range it acts as a short circuit.

The voltage stays the same and you double the resistance. What happens to the current?

It halves. I = V ÷ R, so doubling R halves I.