SMD Soldering and Rework

ReviewedAdvanced ProAbout 6 min
4.98V
In short

SMD Soldering and Rework: the short answer

Surface-mount parts sit on pads instead of going through holes. 5 mm-pitch chips are practical by hand.

Level
Advanced
Time
About 6 min
Topic
Tools and measurement
You will learn to

Solder and remove 0603 passives, SOIC and TSSOP chips and QFN packages with an iron, flux and hot air.

Before this: Through-Hole Soldering That Lasts

Surface-mount parts sit on pads instead of going through holes. With a fine tip, tweezers, good light and plenty of flux, sizes down to 0603 passives and 0.5 mm-pitch chips are practical by hand. For a two-terminal part, tin one pad, hold the part with tweezers, reheat that pad so the part settles flat, then solder the other side and finally touch up the first. For SOIC and TSSOP chips, align the part precisely, tack two opposite corner pins, check alignment under magnification, then solder the rest.

Drag soldering is the fast way to do fine-pitch rows. Flood the pins with flux, load a chisel or hoof tip with a small amount of solder and drag it slowly along the row. Surface tension pulls the solder onto each pad and the flux stops bridges forming. If a bridge does form, add more flux and drag again, or touch it with wick. Clean the flux residue with isopropyl alcohol and inspect every pin under a magnifier.

Hot air is needed for QFN and other parts with pads underneath, and for removing chips. Set about 300 to 350 °C with moderate airflow, preheat the area in circles, then concentrate on the part until all the solder melts and lift it with tweezers; do not pry before it is fully molten or you will tear the pads. For QFN, tin the pads lightly (keep the centre thermal pad thin), add flux, place the part and heat until it drops and self-centres. Protect nearby plastic connectors with Kapton tape, and let the board cool slowly. Moisture-sensitive parts that have absorbed humidity can crack when heated, so bake old stock first if the datasheet says so.

Flux and small amounts

Surface-mount soldering depends on flux, which cleans the metal and lets solder flow. Use plenty of it, and little solder. For a small chip, tin one pad, place the part with tweezers, solder that corner to hold it, check the alignment, then solder the opposite corner and the rest.

For a fine-pitch chip, drag soldering with extra flux and a small amount of solder on a clean tip draws the solder along the row of pins, and a bridge between pins can be cleared with flux and solder wick.

Hot air and removal

Hot air removes and places parts. Set a moderate air speed so small parts are not blown away, heat evenly, and lift a part when the solder under it is fully molten. Keep the board and neighbouring parts from overheating, and pre-heat the board for large areas. Protect plastic parts such as connectors from the heat.

A larger ground pad on the board draws heat away, so give those joints more time.

Inspect and clean

Check the joints under magnification for bridges, lifted pins and tombstoned parts, where one end of a small resistor or capacitor has lifted. Clean the flux with isopropyl alcohol, especially for fine analogue circuits where residue can leak current. Wear eye protection and use extraction for the fumes.

Common mistakes
  • Using too much solder and too little flux on fine-pitch pins.
  • Overheating the board and lifting pads.
  • Leaving flux residue on a sensitive analogue circuit.
Advanced lesson · Pro plan

Practise this lesson with Pro

The explanation above is free for everyone. The practice for Advanced lessons in every domain are part of the Pro plan at ₹999 a month.

With Pro you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "SMD Soldering and Rework"?

Solder and remove 0603 passives, SOIC and TSSOP chips and QFN packages with an iron, flux and hot air.