Learn / Semiconductors / Transistors and MOSFETs

MOSFET Gate Drive and Switching Losses

ReviewedAdvanced ProAbout 6 min
In short

MOSFET Gate Drive and Switching Losses: the short answer

A MOSFET's gate behaves like a capacitor. To switch it on, you charge the gate to well above its threshold; to switch it off, you discharge it.

Level
Advanced
Time
About 6 min
Topic
Semiconductors
You will learn to

Drive power MOSFETs fast and fully on, and estimate conduction and switching losses so they stay cool.

Before this: Transistors & MOSFET Switching, PWM Timing & Actuator Interfaces, Power Budgets and Thermal Design

A MOSFET's gate behaves like a capacitor. To switch it on, you charge the gate to well above its threshold; to switch it off, you discharge it. The datasheet's total gate charge Qg tells you how much charge that takes, and the gate driver's current sets how fast it happens: switching time ≈ Qg ÷ Igate. An IRFZ44N has about 60 nC of gate charge, so a 20 mA microcontroller pin takes around 3 µs to switch it, while a 1 A gate driver does it in about 60 ns.

The threshold voltage (Vgs(th)) is only where the MOSFET starts to conduct, not where it is fully on. RDS(on) is specified at a particular gate voltage, usually 10 V for standard parts and 4.5 V or 2.5 V for logic-level parts. A standard IRFZ44N driven from a 3.3 V ESP32 pin is barely on and gets hot; use a logic-level part such as the IRLZ44N or AO3400A, or a gate driver that provides 10 to 12 V.

Two kinds of loss heat the MOSFET. Conduction loss is I² × RDS(on), and it dominates at low frequency. Switching loss happens during each transition, while the MOSFET has both voltage across it and current through it; a rough estimate is 0.5 × V × I × (tr + tf) × f. At 20 kHz PWM with slow 3 µs edges, switching loss can be many times the conduction loss. Add a small gate resistor (10 to 47 Ω) to damp ringing, a 10 kΩ to 100 kΩ pull-down so the gate is off during reset, and a gate driver such as the IR2110 for high-side or bridge circuits.

The gate is a capacitor

Switching a MOSFET means charging and discharging its gate capacitance, and the datasheet gives this as total gate charge, Qg. The average gate drive current is Qg times the switching frequency, so a part with 30 nC at 100 kHz needs 3 mA on average. A driver with a strong peak current switches it quickly, and a microcontroller pin cannot.

The gate resistor controls the speed. A smaller resistor switches faster with less loss but more ringing and noise; a larger one is calmer but slower.

Switching loss and the Miller plateau

During switching the voltage and current overlap, and that overlap is where the loss comes from. Loss rises in proportion to frequency, so a faster design needs a better-driven device. The flat part of the gate voltage during a transition, called the Miller plateau, is when the drain voltage is moving, so it is the period that matters most.

Total loss is the conduction loss, I squared times Rds(on), plus the switching loss and the gate drive loss.

High-side and bridges

A high-side N-channel MOSFET needs a gate voltage above its source, which a bootstrap circuit or a gate driver chip provides. In a half-bridge, never turn on both switches together, since that shorts the supply. A driver with dead time guarantees a gap between one switching off and the other switching on.

Common mistakes
  • Driving a large MOSFET at high frequency straight from a microcontroller pin.
  • Using a tiny gate resistor and getting ringing and noise.
  • Turning on both switches of a half-bridge at once.
Key formulas
Igate(avg) = Qg × f
average gate drive current
P = I² × Rds(on) + switching loss
conduction plus switching heat

Work it with your own numbers: MOSFET switch

Advanced lesson · Pro plan

Practise this lesson with Pro

The explanation above is free for everyone. The practice for Advanced lessons in every domain are part of the Pro plan at ₹999 a month.

With Pro you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "MOSFET Gate Drive and Switching Losses"?

Drive power MOSFETs fast and fully on, and estimate conduction and switching losses so they stay cool.