Learn / PCB and making / PCB layout

PCB Power Distribution and Grounding

ReviewedAdvanced ProAbout 6 min
In short

PCB Power Distribution and Grounding: the short answer

Every current flows in a loop: out along the supply and back through ground. At high frequencies the return current flows in the ground plane directly underneath its signal track, because that path has the lowest inductance.

Level
Advanced
Time
About 6 min
Topic
PCB and making
You will learn to

Lay out power and ground so mixed-signal boards with motors, radios and ADCs stay quiet and stable.

Before this: PCB Layout Rules That Work, Decoupling and Bulk Capacitors

Every current flows in a loop: out along the supply and back through ground. At high frequencies the return current flows in the ground plane directly underneath its signal track, because that path has the lowest inductance. A solid, unbroken ground plane gives every signal a short return path. Cutting slots in the plane, or routing a track across a gap, forces the return current around it, making a large loop that radiates and picks up noise. On a two-layer board, keep most of the bottom layer as solid ground and route signals mainly on top.

Separate noisy and sensitive areas by placement rather than by splitting the ground. Put the motor driver, buck converter and their high-current loops at one edge near the power input, and the ADC, sensors and crystal at the far side. High currents then return to the input without flowing under the sensitive parts. Keep the switching loops of converters tiny, connect them to the plane with several vias, and keep the switching node copper small. A split analog and digital ground is rarely needed; if you use one, join them at exactly one point under the ADC and never route signals across the split.

Distribute power deliberately. Use wide tracks or pours for supply rails, star the high-current feeds from the input, and place decoupling capacitors with their own vias to ground right at each pin. Add a ferrite bead and capacitor to filter the supply feeding an analog section or a radio. Radio modules need the copper keep-out area under their antenna shown in the datasheet, with no ground or tracks there, and the antenna at the board edge. Finally, put test points on every rail and key signal; you will need them for debugging.

Ground is a path, not a symbol

Current through a track or plane with any resistance or inductance causes a voltage drop, so the ground at one point is not the same as at another. A solid ground plane keeps the difference small. Where a noisy load such as a motor or a switching supply shares ground with a sensitive analogue circuit, route their returns separately and join them at one place, near the supply.

Splitting a ground plane into analogue and digital parts causes problems unless you are sure where the return currents flow. A single unbroken plane with the analogue and digital parts placed in separate areas is usually the safer choice.

Distribute power with care

Bring power from the supply to each section on a wide track or a plane, and put a bulk capacitor where power enters the board and small ceramics at each chip. Check the voltage at the farthest chip under full load, since a long thin track can drop enough to cause resets.

Place the connector's power and ground pins together and keep the loop between them small.

Check in the lab

Measure supply ripple at the chip with a short ground spring on the probe, and compare it with the supply's output. If the noise is larger at the chip, improve the decoupling and the routing, not the supply.

Common mistakes
  • Sharing a ground return between a motor and a sensitive analogue circuit.
  • Splitting the ground plane without knowing where return currents flow.
  • Using a long, thin track to supply a power-hungry part.
Key formulas
V = I × R
every trace has resistance: 1 oz copper is about 0.5 mΩ per square

Work it with your own numbers: Wire voltage drop · PCB trace width

Advanced lesson · Pro plan

Practise this lesson with Pro

The explanation above is free for everyone. The practice for Advanced lessons in every domain are part of the Pro plan at ₹999 a month.

With Pro you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "PCB Power Distribution and Grounding"?

Lay out power and ground so mixed-signal boards with motors, radios and ADCs stay quiet and stable.