Active low-pass, high-pass and band-pass filters
To design first-order active low-pass and high-pass filters with an op-amp and plot their frequency response.
Theory
An RC network followed by a non-inverting amplifier gives a first-order active filter with cut-off fc = 1/(2πRC) and pass-band gain Af = 1 + Rf/R1. Unlike a passive filter, it can have gain and drives a load without changing its response. A band-pass filter can be made by cascading a high-pass and a low-pass section with fL < fH.
Apparatus
- IC 741
- Resistors
- Capacitors 0.01 µF
- Dual supply ±12 V
- Function generator
- CRO
Circuit connections
- Low-pass: input → R → pin 3, C from pin 3 to ground; R1 from pin 2 to ground, Rf from pin 2 to pin 6
- High-pass: swap R and C at the input
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| f (Hz) | Gain | Gain (dB) |
|---|---|---|
| 33 | 1.999 | 6 |
| 78 | 1.994 | 6 |
| 183 | 1.967 | 5.9 |
| 428 | 1.839 | 5.3 |
| 1001 | 1.414 | 3 |
| 2343 | 0.786 | -2.1 |
| 5483 | 0.359 | -8.9 |
| 12831 | 0.156 | -16.2 |
| 30029 | 0.067 | -23.5 |
Precautions
- Keep the input amplitude constant and below clipping.
- Use the nearest standard resistor and note the change in fc.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | f (Hz) | Gain | Gain (dB) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
Your lab record
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the active low-pass, high-pass and band-pass filters experiment?
To design first-order active low-pass and high-pass filters with an op-amp and plot their frequency response.
What apparatus is needed for active low-pass, high-pass and band-pass filters?
IC 741, Resistors, Capacitors 0.01 µF, Dual supply ±12 V, Function generator, CRO.
What is the theory behind active low-pass, high-pass and band-pass filters?
An RC network followed by a non-inverting amplifier gives a first-order active filter with cut-off fc = 1/(2πRC) and pass-band gain Af = 1 + Rf/R1. Unlike a passive filter, it can have gain and drives a load without changing its response. A band-pass filter can be made by cascading a high-pass and a low-pass section with fL < fH.
What result should I get in active low-pass, high-pass and band-pass filters?
fc = ___ Hz (design 1 kHz), pass-band gain = ___ dB, roll-off ≈ 20 dB/decade.
What precautions should I take in active low-pass, high-pass and band-pass filters?
Keep the input amplitude constant and below clipping. Use the nearest standard resistor and note the change in fc.
