Learn / Sensors and actuators / Motors and drivers

Motor Power and Drivers

ReviewedIntermediate MakerAbout 5 min
BME280
In short

Motor Power and Drivers: the short answer

A microcontroller GPIO pin cannot directly power a motor. Select a driver and supply appropriate to startup, stall, noise and protection requirements.

Level
Intermediate
Time
About 5 min
Topic
Sensors and actuators
You will learn to

Choose a motor driver and power supply that handle start-up and stall current.

Before this: Transistors & MOSFET Switching

A microcontroller GPIO pin cannot directly power a motor. Select a driver and supply appropriate to startup, stall, noise and protection requirements.

Motors are inductive loads whose inrush and stall behavior can exceed ordinary operating current. Drivers provide appropriate switching paths; protecting the controller requires electrical, thermal and sometimes mechanical precautions.

Prepare a driver-selection table with supply voltage, stall current, reverse-polarity protection, control thresholds and fault signaling. Keep outputs stopped until a qualified review approves any powered experiment.

Start-up and stall are the real loads

A motor's label shows its running current. At the instant it starts, and any time its shaft is held, it draws several times more, limited only by the winding resistance. A small brushed motor rated 0.5 A running can pull 3 to 5 A when stalled. Choose the driver and supply for the stall current, or add current limiting that stops a stall from lasting.

You can estimate stall current from the coil: stall current ≈ supply voltage ÷ winding resistance. Measure the resistance with a multimeter on the motor with the shaft still.

Picking a driver

A single MOSFET with a flyback diode switches one direction and works for a fan or a pump. An H-bridge such as the L298N, TB6612 or DRV8833 also reverses the motor. The L298N is old and wasteful, dropping around 2 V across itself, which is a lot on a 6 V motor; the TB6612 and DRV8833 drop much less and run cooler. Stepper motors use their own drivers (A4988, DRV8825, TMC series) with a current limit you set to the motor's rating.

Check four numbers in the driver's datasheet: supply voltage range, continuous current and peak current, logic voltage (3.3 V or 5 V), and whether it has thermal and over-current protection.

Protecting the controller

Brushes and coils make electrical noise that resets microcontrollers. Fit a 100 nF ceramic capacitor across the motor terminals, close to the motor, and a larger capacitor (100 to 470 µF) across the driver's supply. Keep motor wires away from signal wires, and join grounds at a single point. If resets continue, power the motor from a separate supply from the logic, with only the grounds joined.

Never connect a motor directly to a GPIO pin, and never remove a flyback diode because the circuit seemed to work without it. It can fail later, in a way that damages the pin or the board.

Safe bring-up

Test with the motor unloaded and the supply current-limited, if you have a bench supply, at a low voltage first. Watch the current on the supply's display and stop at once if it climbs or the driver smells hot. Have a way to cut power quickly. Keep fingers, hair and loose clothing away from anything that can spin or pinch.

Write down a stop rule in code: if no command arrives for a second, stop the motor. A crash in your program should leave the motor off, not running.

Common mistakes
  • Sizing the supply for the running current instead of the stall current.
  • Sharing one thin ground wire between motor and logic.
  • Using a driver that drops 2 V on a 6 V motor and wondering why it is weak and hot.
Intermediate lesson · Maker plan

Practise this lesson with Maker

The explanation above is free for everyone. The practice for Intermediate lessons in every domain are part of the Maker plan at ₹499 a month, and Pro includes them too.

With Maker you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "Motor Power and Drivers"?

Choose a motor driver and power supply that handle start-up and stall current.