Learn / Basics / Series and parallel

Thevenin Equivalents and Loading

ReviewedIntermediate MakerAbout 6 min
Vout = 2.5 V
In short

Thevenin Equivalents and Loading: the short answer

Thevenin's theorem says that any circuit made of voltage sources and resistors, seen from two terminals, behaves exactly like one voltage source Vth in series with one resistor Rth. This is the most useful shortcut in practical electronics, because it tells you at once how much a circuit's output will drop when you connect something to it.

Level
Intermediate
Time
About 6 min
Topic
Basics
You will learn to

Replace any network of sources and resistors with one voltage and one resistance, and predict what happens when you connect a load.

Before this: Kirchhoff's Laws, Resistor Networks & Loading

Thevenin's theorem says that any circuit made of voltage sources and resistors, seen from two terminals, behaves exactly like one voltage source Vth in series with one resistor Rth. This is the most useful shortcut in practical electronics, because it tells you at once how much a circuit's output will drop when you connect something to it.

To find Vth, disconnect the load and work out (or measure) the open-circuit voltage between the two terminals. To find Rth, replace every voltage source with a plain wire and work out the resistance looking back into the terminals. For a voltage divider made of R1 on top and R2 at the bottom, Vth = Vin × R2 ÷ (R1 + R2) and Rth is R1 and R2 in parallel. You can also measure Rth on the bench: measure the open-circuit voltage, then add a known load and measure again; the drop tells you Rth.

Once you have the equivalent, loading is easy: the load RL and Rth form a new divider, so the output becomes Vth × RL ÷ (Rth + RL). The output stays within 10 % of Vth only when RL is at least about ten times Rth. The same picture explains why a battery's voltage sags under load (its internal resistance is Rth) and why a sensor with a high output resistance needs a buffer before a low-resistance input. Maximum power reaches the load when RL equals Rth, but at that point half the power is wasted in Rth, so power electronics aims for RL much larger than Rth instead.

Any two-terminal network is a source and a resistor

However many parts a network has, seen from two terminals it behaves like one voltage source in series with one resistor. The source value is the open-circuit voltage. The resistance is what you see looking back into the terminals with the sources turned off, meaning voltage sources replaced by a wire and current sources by an open circuit.

A divider of 10 kΩ and 10 kΩ from 5 V has an open-circuit voltage of 2.5 V and a Thevenin resistance of 5 kΩ, the two resistors in parallel.

Why it explains loading

Connect a load and it forms a divider with the Thevenin resistance. A 5 kΩ load on that divider gives 1.25 V instead of 2.5 V. A rule of thumb is that the load should be at least ten times the source resistance if you want the voltage to drop by less than about 10 percent.

The same idea applies to sensors and ADC inputs. A high-resistance sensor feeding an ADC input that needs a low source impedance reads wrongly until you add a buffer.

Maximum power

A load draws the most power from a source when its resistance equals the Thevenin resistance, but then half the power is lost inside the source. For efficiency, as with a battery or a power supply, you want the load much larger than the source resistance.

Common mistakes
  • Forgetting to turn off the sources when finding the Thevenin resistance.
  • Ignoring the loading of a divider by the next stage.
  • Applying maximum power transfer to a power supply, where it wastes half the energy.
Key formulas
Vout = Vth × RL ÷ (Rth + RL)
a source with internal resistance Rth driving a load RL
Rth = Voc ÷ Isc
open-circuit voltage over short-circuit current
Try it: Load a source

Output against load

0 V2 V4 V10 Ω100 Ω1 kΩ10 kΩ100 kΩLoad RL4.55 V

Any real source has an internal (Thevenin) resistance. A small load pulls its voltage down.

Vout = 4.55 V (91 % of Vth)

Vout against load rl. With RL = Rth the output is exactly half of Vth.

Work it with your own numbers: Loaded divider

Intermediate lesson · Maker plan

Practise this lesson with Maker

The explanation above is free for everyone. The practice for Intermediate lessons in every domain are part of the Maker plan at ₹499 a month, and Pro includes them too.

With Maker you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "Thevenin Equivalents and Loading"?

Replace any network of sources and resistors with one voltage and one resistance, and predict what happens when you connect a load.