Transient response of RC and RL circuits
To observe the charging and discharging of a capacitor through a resistor and measure the time constant τ = RC (and τ = L/R for an RL circuit).
Theory
When a step voltage V is applied, the capacitor voltage rises as Vc = V(1 − e^(−t/τ)), with τ = RC. After one τ it reaches 63.2% of V, and after 5τ it is practically full. Discharging follows Vc = V·e^(−t/τ). In an RL circuit the current rises the same way with τ = L/R.
Apparatus
- Function generator (square wave) or DC supply with a switch
- Resistor 10 kΩ
- Capacitor 10 µF (or 0.1 µF with a square wave)
- CRO or multimeter and stopwatch
Circuit connections
- Supply (or square wave) → R → C → ground; CRO across C
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| t (ms) | t / τ | Vc charging (V) | Vc discharging (V) |
|---|---|---|---|
| 0 | 0 | 0 | 5 |
| 50 | 0.5 | 1.967 | 3.033 |
| 100 | 1 | 3.161 | 1.839 |
| 200 | 2 | 4.323 | 0.677 |
| 300 | 3 | 4.751 | 0.249 |
| 400 | 4 | 4.908 | 0.092 |
| 500 | 5 | 4.966 | 0.034 |
Precautions
- Connect the electrolytic capacitor with the right polarity.
- Discharge the capacitor before each new run.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | t (ms) | t / τ | Vc charging (V) | Vc discharging (V) |
|---|---|---|---|---|
| 1 | ||||
| 2 | ||||
| 3 | ||||
| 4 | ||||
| 5 | ||||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
Your lab record
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the transient response of rc and rl circuits experiment?
To observe the charging and discharging of a capacitor through a resistor and measure the time constant τ = RC (and τ = L/R for an RL circuit).
What apparatus is needed for transient response of rc and rl circuits?
Function generator (square wave) or DC supply with a switch, Resistor 10 kΩ, Capacitor 10 µF (or 0.1 µF with a square wave), CRO or multimeter and stopwatch.
What is the theory behind transient response of rc and rl circuits?
When a step voltage V is applied, the capacitor voltage rises as Vc = V(1 − e^(−t/τ)), with τ = RC. After one τ it reaches 63.2% of V, and after 5τ it is practically full. Discharging follows Vc = V·e^(−t/τ). In an RL circuit the current rises the same way with τ = L/R.
What result should I get in transient response of rc and rl circuits?
Measured τ = ___ ms; calculated RC = ___ ms. The capacitor voltage follows the exponential law.
What precautions should I take in transient response of rc and rl circuits?
Connect the electrolytic capacitor with the right polarity. Discharge the capacitor before each new run.
