Using a Multimeter

ReviewedBeginnerFreeAbout 5 min
4.98V
In short

Using a Multimeter: the short answer

A multimeter measures voltage across points and current in series with a circuit. Incorrect current range or placement can short a supply. Example: 12.4 mA, close to the 13.6 mA you calculated with 220 Ω. Putting the lead back on V prevents the classic blown-fuse mistake.

Level
Beginner
Time
About 5 min
Topic
Tools and measurement
You will learn to

Measure voltage, current and resistance safely with a multimeter.

Before this: Voltage, Current & Resistance

A multimeter measures voltage across points and current in series with a circuit. Incorrect current range or placement can short a supply.

Voltage measurements are made across terminals using a suitable selected range. Current measurement requires inserting the meter correctly into the circuit using the right fused input and mode. Resistance measurement ordinarily requires power disconnected.

Before every measurement, identify the instrument lead sockets, expected maximum quantity, circuit energy and meter category. An incorrectly placed current lead can short a supply even when the meter display looks normal.

The dial and the sockets

Most meters have three or four sockets. COM is always where the black lead goes. The red lead goes into V/Ω for voltage, resistance, continuity and diode tests; into mA for small currents; and into 10 A (or 20 A) for large ones. The mA and 10 A sockets connect the red lead almost straight to COM through a shunt and fuse, which is why a lead left in a current socket is dangerous when you then measure a voltage.

Make one habit: after any current measurement, move the red lead back to V/Ω before you do anything else.

Voltage: across, with power on

Touch the black lead to ground and the red to the point you want. On a board, measure straight on the pin or pad, not just at the supply, because wires, connectors and breadboard contacts all drop voltage. A 5 V supply that reads 4.6 V at the chip tells you something real about the wiring.

DC and AC are different settings. On an auto-ranging meter, choose V⎓ (DC) for batteries and boards, and V~ (AC) only for mains-side transformer outputs, and only if you have been taught how to do that safely.

Current: through, with the circuit broken

Switch off, move the red lead to mA, break the circuit at one point, and bridge the gap with the meter. Switch on and read. The meter's shunt adds a small resistance (the burden), which can lower the current slightly in low-voltage circuits, or reset a microcontroller that suddenly draws more on Wi-Fi bursts. Start on the 10 A socket if you are not sure of the size.

For a quick sleep-current check on battery projects, measure in the battery lead. For a board's peak current, a USB power meter is often easier.

Resistance and continuity: power off

The meter measures resistance by pushing its own small current through the part. Any other voltage in the circuit upsets the reading and can damage the meter, so always unplug first. Measured in-circuit, a resistor often reads lower than its value because other parts are in parallel with it; lift one leg to be sure.

Continuity mode beeps below a few tens of ohms. It is the fastest way to check a breadboard row, a cable or a solder joint, and to find a short between supply and ground before you power a new board.

Safety ratings mean something

Meters carry CAT ratings (CAT II, CAT III) that say how big a spike they can survive. A cheap meter with no rating, or worn leads with cracked insulation, is fine for 5 V projects and not fine anywhere near mains. If a project touches mains, ask someone qualified to help, and keep your low-voltage meter for the low-voltage side.

Common mistakes
  • Measuring voltage with the red lead still in the mA socket: a short circuit through the meter.
  • Measuring resistance with the circuit powered.
  • Reading the wrong range: 4.98 on the 20 V range is 4.98 V; 498 on the 2000 mV range is 498 mV.
Worked example

Measure what an LED circuit actually draws

  1. Unplug power. Move the red lead to the mA socket and set the dial to mA.
  2. Break the circuit between the resistor and the LED; put the meter across the gap.
  3. Power on: it reads 12.4 mA.
  4. Power off, move the red lead back to V before measuring anything else.

Result. 12.4 mA, close to the 13.6 mA you calculated with 220 Ω. Putting the lead back on V prevents the classic blown-fuse mistake.

Try it

Practice voltage measurement across a safe low-voltage battery under supervision.

Check yourself

3 quick questions

  1. How do you measure the voltage across an LED?

  2. Why measure resistance with power off?

  3. You measured current and now want voltage. What first?

Common questions

What will I learn in "Using a Multimeter"?

Measure voltage, current and resistance safely with a multimeter.

How do I measure what an LED circuit actually draws?

Unplug power. Move the red lead to the mA socket and set the dial to mA. Break the circuit between the resistor and the LED; put the meter across the gap. Power on: it reads 12.4 mA. Power off, move the red lead back to V before measuring anything else. 12.4 mA, close to the 13.6 mA you calculated with 220 Ω. Putting the lead back on V prevents the classic blown-fuse mistake.

How do you measure the voltage across an LED?

Meter probes on each LED leg, circuit powered. Voltage is measured across a part while it is powered.

Why measure resistance with power off?

The meter supplies its own small current, and live voltage gives wrong readings or damage. The ohms range injects its own current; external voltage corrupts the reading.

You measured current and now want voltage. What first?

Move the red lead back to the V socket. A lead left in the current socket shorts whatever you probe next.