Lab / Analog and linear ICs

Op-amp inverting and non-inverting amplifiers

To build inverting and non-inverting amplifiers with a 741 op-amp and verify their gain.

Analog and linear ICsVirtual readings4 viva questions
−+Vout = −Rf/Rin · Vin

Theory

With negative feedback the op-amp keeps its two inputs at nearly the same voltage. Inverting amplifier: Av = −Rf/Rin, and the input sits at virtual ground. Non-inverting amplifier: Av = 1 + Rf/Rin, with very high input resistance. With Rf = 0 and Rin open, the non-inverting stage is a unity-gain voltage follower. The output cannot swing beyond about ±(Vcc − 1.5 V).

Apparatus

  • IC 741 (or LM358)
  • Resistors 1 kΩ, 10 kΩ, 100 kΩ
  • Dual supply ±12 V
  • Function generator
  • CRO

Circuit connections

  • Inverting: input → Rin → pin 2; Rf from pin 2 to pin 6; pin 3 to ground
  • Non-inverting: input → pin 3; Rin from pin 2 to ground; Rf from pin 2 to pin 6
  • Pin 7 to +12 V, pin 4 to −12 V

Procedure

Pre-lab check

4 questions · 75% to be ready
1What is virtual ground?
2List the ideal op-amp characteristics.
3What is slew rate?
4Why is a voltage follower used?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
Gain-10
-12-5.805.812-1-0.500.51Vin (V)Vout (V)
Vin (V)Vout ideal (V)Vout (V, ±10.5 V limit)
-11010
-0.555
-0.222
-0.111
000
0.1-1-1
0.2-2-2
0.5-5-5
1-10-10

Precautions

  • Switch on both supplies together and check pin numbers before power-up.
  • Keep the input small enough to avoid clipping.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.Vin (V)Vout ideal (V)Vout (V, ±10.5 V limit)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book

Your lab record

Result formatMeasured gain: inverting ___ (theory −Rf/Rin = ___), non-inverting ___ (theory 1 + Rf/Rin = ___). The inverting output is 180° out of phase.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva practice

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What is virtual ground?
2. List the ideal op-amp characteristics.
3. What is slew rate?
4. Why is a voltage follower used?

Quick answers for your record and viva

What is the aim of the op-amp inverting and non-inverting amplifiers experiment?

To build inverting and non-inverting amplifiers with a 741 op-amp and verify their gain.

What apparatus is needed for op-amp inverting and non-inverting amplifiers?

IC 741 (or LM358), Resistors 1 kΩ, 10 kΩ, 100 kΩ, Dual supply ±12 V, Function generator, CRO.

What is the theory behind op-amp inverting and non-inverting amplifiers?

With negative feedback the op-amp keeps its two inputs at nearly the same voltage. Inverting amplifier: Av = −Rf/Rin, and the input sits at virtual ground. Non-inverting amplifier: Av = 1 + Rf/Rin, with very high input resistance. With Rf = 0 and Rin open, the non-inverting stage is a unity-gain voltage follower. The output cannot swing beyond about ±(Vcc − 1.5 V).

What result should I get in op-amp inverting and non-inverting amplifiers?

Measured gain: inverting ___ (theory −Rf/Rin = ___), non-inverting ___ (theory 1 + Rf/Rin = ___). The inverting output is 180° out of phase.

What precautions should I take in op-amp inverting and non-inverting amplifiers?

Switch on both supplies together and check pin numbers before power-up. Keep the input small enough to avoid clipping.

Op-amp inverting and non-inverting amplifiers | ElectroLark