Inductors, LC Filters and Noise

ReviewedAdvanced ProAbout 6 min
In short

Inductors, LC Filters and Noise: the short answer

An inductor resists changes in current: V = L × di/dt. Try to stop the current in a relay coil or motor suddenly and the inductance produces a large voltage spike, which is why those loads need a flyback diode.

Level
Advanced
Time
About 6 min
Topic
Passive components
You will learn to

Choose inductors by their current ratings, design an LC filter and reduce electrical noise in a circuit.

Before this: Capacitors & Inductors, Buck and Boost Converters

An inductor resists changes in current: V = L × di/dt. Try to stop the current in a relay coil or motor suddenly and the inductance produces a large voltage spike, which is why those loads need a flyback diode. In converters and filters the same property smooths current.

Power inductors have two current ratings, and both matter. The saturation current is where the core can no longer store more energy and the inductance collapses, so current rises sharply. The RMS or heating current is where the winding gets too hot. Choose an inductor with both ratings comfortably above your peak and average current; a 10 µH part that saturates at 1 A behaves like a piece of wire at 2 A.

An inductor in series with a capacitor to ground forms an LC low-pass filter. It resonates at f0 = 1 ÷ (2π√(LC)) and falls by about 100 times for every ten times increase in frequency above that, much steeper than an RC filter, without wasting power in a resistor. It can also ring at f0, so add some resistance, for example the capacitor's ESR or a small resistor in series with an extra capacitor. Ferrite beads are lossy inductors that turn high-frequency noise into heat; they are good on supply lines to sensitive parts. The biggest noise fix, though, is layout: keep the loop formed by a switching current and its return path as small as possible.

Energy storage and resonance

An inductor stores energy in its magnetic field and resists changes in current. With a capacitor it forms a resonant circuit at a frequency of 1 ÷ (2π √(LC)). An LC low-pass filter reduces ripple and noise much more steeply than a single RC, and with little loss because an inductor does not waste energy as heat the way a resistor does.

A 10 µH inductor with a 10 µF capacitor resonates near 16 kHz, so it filters well above that, but it can ring at that frequency if it is not damped.

Choosing and using

Check the inductance, the saturation current, the heating current and the series resistance. A ferrite bead is a lossy inductor used to block high-frequency noise on a supply or a cable. A common-mode choke reduces noise that travels the same way on both wires of a pair.

A filter in front of a switching supply or on a cable leaving the enclosure reduces the noise that other equipment sees, which helps with compliance tests.

Where noise comes from

Fast edges and large loops make interference. Keep loops small, keep the return path under the signal, and place filters at the point where a cable enters the board.

Common mistakes
  • Using an inductor past its saturation current.
  • Building an LC filter with no damping and getting ringing.
  • Adding a filter far from where the noise leaves the board.
Key formulas
XL = 2πfL
inductor reactance
f0 = 1 ÷ (2π√(LC))
LC resonant frequency
Try it: Find resonance

Where the two reactances cross

10 Ω100 Ω1 kΩ10 kHz100 kHz1 MHzFrequency159 kHz

XL rises with frequency and Xc falls. Where they cross, they cancel: that is the resonant frequency.

f0 = 1 ÷ (2π√(LC)) = 159 kHz

XL (inductor)Xc (capacitor)Reactance against frequency. XL rises and Xc falls; they are equal at 159 kHz, the resonant frequency.

Work it with your own numbers: LC resonance · Inductive reactance

Advanced lesson · Pro plan

Practise this lesson with Pro

The explanation above is free for everyone. The practice for Advanced lessons in every domain are part of the Pro plan at ₹999 a month.

With Pro you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "Inductors, LC Filters and Noise"?

Choose inductors by their current ratings, design an LC filter and reduce electrical noise in a circuit.