Reading and Choosing Resistors: the short answer
A through-hole resistor shows its value as colour bands. On a 4-band resistor the first two bands are digits, the third is the multiplier (how many zeros to add) and the fourth is the tolerance. Example: Use 220 Ω (red, red, brown, gold). The LED runs at about 14 mA and the resistor stays cool.
- Level
- Beginner
- Time
- About 6 min
- Topic
- Passive components
Read a resistor's value from its colour bands and pick the right value, tolerance and power rating.
Before this: Ohm’s Law, Power & Heat
A through-hole resistor shows its value as colour bands. On a 4-band resistor the first two bands are digits, the third is the multiplier (how many zeros to add) and the fourth is the tolerance. Brown, black, red, gold means 1, 0, × 100 = 1,000 Ω, which is 1 kΩ ± 5 %. On a 5-band resistor the first three bands are digits.
Values come from standard series. E12 has twelve steps per decade (1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2), which is why you find 220 Ω and 4.7 kΩ in every kit but not 250 Ω. When your calculation gives a value between two steps, pick the next higher one for current limiting, so the current ends up a little lower rather than higher.
Tolerance tells you how far the real value may be from the marking: a 1 kΩ ± 5 % part can measure anywhere from 950 to 1,050 Ω. Metal film parts (usually blue, ± 1 %) are better for dividers and measurement; carbon film (beige, ± 5 %) is fine for LEDs and pull-ups. Finally, check the power: P = I² × R must stay well under the rating, which is 1/4 W for common parts.
Reading the bands without guessing the direction
The tolerance band (gold, silver, or brown for 1 %) sits a little apart from the others and is read last. If the bands are evenly spaced, the first band is the one nearest the edge. When in doubt, a multimeter settles it in a second, with the resistor out of circuit.
The digit colours are the same everywhere: black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8, white 9. For the multiplier, gold is ×0.1 and silver ×0.01. So orange, orange, brown is 33 × 10 = 330 Ω, and green, blue, orange is 56 × 1,000 = 56 kΩ.
Why the values are odd numbers
Each E-series step is about the same percentage bigger than the last, so the values are spread evenly in a ratio, not in a count. E12 has 10 % steps and suits 10 % parts; E24 has 5 % steps; E96 has 1 % steps. A tighter series is only worth buying if the part's tolerance is tight too.
To make a value you cannot buy, combine two: two resistors in series add, and in parallel give less than the smaller. A 2.5 kΩ target can be 2.2 kΩ + 330 Ω (2.53 kΩ) with the standard parts you already own.
Tolerance and temperature in a real circuit
A 5 % pair in a voltage divider can give an output that is off by up to about 5 % of the supply fraction, which matters when you measure a battery. For dividers, ADC references and amplifier gains use 1 % metal film. For LED current limiting and pull-ups, tolerance does not matter at all, because the circuit works across a wide range.
Resistors also change with temperature, by about 100 ppm per degree for metal film, which is 0.1 % for a 10 °C rise. Fine for most work, but it explains why precision parts specify a low temperature coefficient.
SMD resistors and marking codes
Surface-mount resistors print a number code instead of bands. Three digits: 103 means 10 followed by three zeros, 10 kΩ. 4R7 means 4.7 Ω, where R marks the decimal point. 01C and similar codes on 1 % parts are E96 codes that need a lookup table. Always confirm with a meter when a drawer is unlabelled.
- Reading the bands from the wrong end.
- Mixing up red and brown, or orange and red, in dim light. Check with a meter when value matters.
- Using the next value down for LED current limiting, which raises the current instead of lowering it.
Pick a resistor for a red LED on 5 V at about 15 mA
- Red LED drop is about 2.0 V, so the resistor sees 5 − 2 = 3 V.
- R = 3 V ÷ 0.015 A = 200 Ω.
- 200 Ω is not in E12. The next higher value is 220 Ω.
- Check current: 3 ÷ 220 = 13.6 mA. Power: 3 × 0.0136 = 0.04 W, far below 1/4 W.
Result. Use 220 Ω (red, red, brown, gold). The LED runs at about 14 mA and the resistor stays cool.
Take five resistors from your kit, read each one by its bands, then measure it with your multimeter on the Ω range. Note whether each measured value is inside its tolerance.
3 quick questions
What value is yellow, violet, red, gold?
Your calculation gives 300 Ω for an LED. Which E12 value do you choose?
A 1 kΩ ± 5 % resistor measures 1,080 Ω. What does that tell you?
