Lab / Analog and linear ICs

555 timer as an astable multivibrator

To design a 555 astable multivibrator for a given frequency and duty cycle and measure its output.

Analog and linear ICsVirtual readings4 viva questions
555

Theory

The capacitor charges through R1 + R2 from ⅓Vcc to ⅔Vcc and discharges through R2. High time tH = 0.693(R1 + R2)C, low time tL = 0.693·R2·C, frequency f = 1.44/((R1 + 2R2)C) and duty cycle D = (R1 + R2)/(R1 + 2R2), which is always above 50% in the basic circuit.

Apparatus

  • IC NE555
  • Resistors R1, R2
  • Capacitors C and 0.01 µF (control pin)
  • DC supply 5–12 V
  • CRO
  • LED with 470 Ω (optional)

Circuit connections

  • Pin 8 and 4 to Vcc, pin 1 to ground
  • R1 from Vcc to pin 7, R2 from pin 7 to pins 6 and 2, C from pins 6 and 2 to ground
  • 0.01 µF from pin 5 to ground; output at pin 3

Procedure

Pre-lab check

4 questions · 75% to be ready
1Between which levels does the capacitor charge and discharge?
2How do you get a duty cycle below 50%?
3What is the reset pin for?
4Name uses of an astable 555.

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
QuantityValue
tH0.5405 ms
tL0.4712 ms
Frequency988.4 Hz
Duty cycle53.4 %

Precautions

  • Keep R1 at least 1 kΩ so the discharge transistor is not overloaded.
  • Use the 0.01 µF capacitor on pin 5 against noise.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.QuantityValue
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book

Your lab record

Result formatDesigned f = ___ Hz, D = ___ %. Measured f = ___ Hz, D = ___ %.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva practice

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. Between which levels does the capacitor charge and discharge?
2. How do you get a duty cycle below 50%?
3. What is the reset pin for?
4. Name uses of an astable 555.

Quick answers for your record and viva

What is the aim of the 555 timer as an astable multivibrator experiment?

To design a 555 astable multivibrator for a given frequency and duty cycle and measure its output.

What apparatus is needed for 555 timer as an astable multivibrator?

IC NE555, Resistors R1, R2, Capacitors C and 0.01 µF (control pin), DC supply 5–12 V, CRO, LED with 470 Ω (optional).

What is the theory behind 555 timer as an astable multivibrator?

The capacitor charges through R1 + R2 from ⅓Vcc to ⅔Vcc and discharges through R2. High time tH = 0.693(R1 + R2)C, low time tL = 0.693·R2·C, frequency f = 1.44/((R1 + 2R2)C) and duty cycle D = (R1 + R2)/(R1 + 2R2), which is always above 50% in the basic circuit.

What result should I get in 555 timer as an astable multivibrator?

Designed f = ___ Hz, D = ___ %. Measured f = ___ Hz, D = ___ %.

What precautions should I take in 555 timer as an astable multivibrator?

Keep R1 at least 1 kΩ so the discharge transistor is not overloaded. Use the 0.01 µF capacitor on pin 5 against noise.

555 timer as an astable multivibrator: lab experiment