Zener Diodes and Simple Voltage References: the short answer
A normal diode conducts in one direction and blocks the other until it breaks down at a high voltage. 1 V or 12 V, and to survive doing so.
- Level
- Intermediate
- Time
- About 6 min
- Topic
- Semiconductors
Use a Zener diode to clamp or set a voltage, choose its series resistor and know when a regulator is the better choice.
Before this: Diodes, LEDs & Polarity, Ohm’s Law, Power & Heat
A normal diode conducts in one direction and blocks the other until it breaks down at a high voltage. A Zener diode is designed to break down at a precise, low voltage, such as 3.3 V, 5.1 V or 12 V, and to survive doing so. Connected in reverse (cathode, the striped end, to the positive side) with a resistor in series from the supply, it holds the voltage across itself close to its rated Zener voltage even when the supply changes.
The series resistor sets the current. It must pass enough current for the load plus a minimum Zener current (a few milliamps for common 1N47xx parts) at the lowest supply voltage, and the Zener must handle the power when the load is removed at the highest supply voltage. Common 1N47xx Zeners are rated 1 W; keep them under about half of that. Because all the spare current flows through the Zener, this regulator is wasteful and only suits small loads of a few milliamps to a few tens of milliamps.
Zeners are more often used for protection and references than for power. A 5.1 V Zener across an input clamps spikes; a 3.3 V Zener with a resistor protects a 3.3 V microcontroller input from a 5 V signal. Their voltage varies with current and temperature (typically ±5 %), so for an accurate ADC reference use a dedicated reference IC such as a TL431 instead. For powering circuits, use a linear regulator or a buck converter.
Breakdown is the feature
A zener diode is used in reverse. Once the reverse voltage reaches its rating, it conducts and holds the voltage nearly constant. A 5.1 V zener with a series resistor from a higher supply gives about 5.1 V across it, as long as enough current flows through it.
The series resistor sets that current: R = (Vin − Vz) ÷ (Iz + Iload). It must supply the load current plus the minimum zener current, which datasheets give as a few milliamps.
Power and the limits
The zener dissipates Vz times its current, so a 500 mW part at 5.1 V can carry about 98 mA at most, and you should stay well below that. The worst case for it is when the load is removed and all the current flows through the zener.
A zener regulator is simple but wasteful, and its voltage drifts with temperature and current. The tolerance of the rating, often 5 percent, applies too. For a load that changes a lot or needs power, use a regulator IC; use a zener for a reference, for clamping an input or for protecting a pin.
Protecting an input
A 3.3 V zener across a microcontroller input, with a series resistor, clips a higher signal. Choose the resistor so the zener current stays within its limit at the highest expected input, and remember zener capacitance slows fast signals.
- Choosing the series resistor for the load only, so the zener has no current when the load is light.
- Using a zener as a power regulator and overheating it.
- Forgetting what happens when the load is disconnected.
- R = (Vin − Vz) ÷ (Iz + Iload)
- series resistor for a Zener regulator
- Pz = Vz × Iz
- power in the Zener
Work it with your own numbers: Zener resistor
Practise this lesson with Maker
The explanation above is free for everyone. The practice for Intermediate lessons in every domain are part of the Maker plan at ₹499 a month, and Pro includes them too.
With Maker you also get: a worked example, a hands-on task, a 3-question check.
