Lab / Circuits and measurements

Using the multimeter, CRO and function generator

To measure voltage, current, resistance and frequency, and read the amplitude, period and phase of a signal on a CRO.

Circuits and measurementsVirtual readings4 viva questions

Theory

A multimeter measures DC and AC voltage across a part, current through it (in series) and resistance with the part out of circuit. A CRO plots voltage against time: amplitude is divisions × volts/div, period is divisions × time/div, and frequency is 1/period. With two channels the phase difference is φ = (Δt / T) × 360°, where Δt is the time between matching points on the two waves.

Apparatus

  • Digital multimeter
  • CRO (dual channel)
  • Function generator
  • Resistors 1 kΩ, 10 kΩ
  • Capacitor 0.1 µF
  • Breadboard and wires

Circuit connections

  • Function generator output to CRO CH1, ground clips together
  • For phase: generator → 1 kΩ → 0.1 µF → ground; CH1 across the input, CH2 across the capacitor

Procedure

Pre-lab check

4 questions · 75% to be ready
1What does the time/div knob set?
2Why connect both probe grounds to the same point?
3How do you find the phase difference between two waves?
4Why does a multimeter read RMS on AC?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
Corner frequency fc = 1 / (2πRC)1.59 kHz
FrequencyPeriod (ms)Vc / VinPhase lag (°)Δt (µs)
100 Hz100.9983.699.9
500 Hz20.95417.496.9
1 kHz10.84732.189.3
2 kHz0.50.62351.571.5
5 kHz0.20.30372.340.2

Precautions

  • Join the ground clips of both probes to the same point.
  • Use the CRO's calibration before reading divisions.
  • Measure resistance only with the power off.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.FrequencyPeriod (ms)Vc / VinPhase lag (°)Δt (µs)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book

Your lab record

Result formatThe frequency and amplitude read on the CRO agree with the generator settings within the reading error, and the measured phase lag matches φ = tan⁻¹(2πfRC).

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva practice

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What does the time/div knob set?
2. Why connect both probe grounds to the same point?
3. How do you find the phase difference between two waves?
4. Why does a multimeter read RMS on AC?

Quick answers for your record and viva

What is the aim of the using the multimeter, cro and function generator experiment?

To measure voltage, current, resistance and frequency, and read the amplitude, period and phase of a signal on a CRO.

What apparatus is needed for using the multimeter, cro and function generator?

Digital multimeter, CRO (dual channel), Function generator, Resistors 1 kΩ, 10 kΩ, Capacitor 0.1 µF, Breadboard and wires.

What is the theory behind using the multimeter, cro and function generator?

A multimeter measures DC and AC voltage across a part, current through it (in series) and resistance with the part out of circuit. A CRO plots voltage against time: amplitude is divisions × volts/div, period is divisions × time/div, and frequency is 1/period. With two channels the phase difference is φ = (Δt / T) × 360°, where Δt is the time between matching points on the two waves.

What result should I get in using the multimeter, cro and function generator?

The frequency and amplitude read on the CRO agree with the generator settings within the reading error, and the measured phase lag matches φ = tan⁻¹(2πfRC).

What precautions should I take in using the multimeter, cro and function generator?

Join the ground clips of both probes to the same point. Use the CRO's calibration before reading divisions. Measure resistance only with the power off.

Using the multimeter, CRO and function generator