Constant-Current LED Drivers

ReviewedAdvanced ProAbout 6 min
In short

Constant-Current LED Drivers: the short answer

An LED's brightness depends on its current, not its voltage, and its forward voltage falls as it warms up. With just a resistor on a fixed supply, a hot LED takes more current, heats more, and can run away.

Level
Advanced
Time
About 6 min
Topic
Semiconductors
You will learn to

Drive power LEDs at a steady current using linear and switching drivers, and handle their heat.

Before this: LEDs and Current Limiting, Linear Regulators and Heat, Buck and Boost Converters

An LED's brightness depends on its current, not its voltage, and its forward voltage falls as it warms up. With just a resistor on a fixed supply, a hot LED takes more current, heats more, and can run away. For indicator LEDs at a few milliamps, a resistor is fine. For power LEDs (350 mA, 700 mA or more) and long strings, use a constant-current driver that measures the current and adjusts to hold it steady.

The simplest linear driver uses a sense resistor and a feedback element. An LM317 wired as a current source holds 1.25 V across a resistor between its OUT and ADJ pins, so the current is 1.25 ÷ R: 3.6 Ω gives about 350 mA. A two-transistor circuit or an op-amp and MOSFET do the same with less voltage loss. Linear drivers waste (supply voltage − LED voltage) × current as heat, so they suit supplies only a little above the LED's forward voltage.

Switching drivers (buck LED drivers such as those on common 3 W LED modules) convert the extra voltage efficiently and are the right choice for higher power or when the supply is much higher than the LED string. Dimming is done with PWM on the driver's enable or dim pin, which keeps the colour constant, rather than by lowering the current. Heat is the real limit: a 3 W LED needs a metal-core PCB and a heatsink, and its light output and life both fall as the junction gets hotter.

An LED wants current, not voltage

An LED's voltage drop changes with temperature and between parts, and a small change in voltage causes a large change in current. A resistor from a fixed supply works for one small LED, but for a power LED you need to control the current directly. A constant-current driver senses the current through a small resistor and adjusts itself to keep it steady.

The simplest forms are a linear driver, such as a transistor with a sense resistor, or a dedicated chip. A switching driver wastes much less heat and suits high power.

Headroom and heat

A linear driver wastes (supply voltage − LED voltage) × current as heat, so keep that difference small, and check the driver's minimum voltage headroom. A 12 V supply driving one 3 V LED at 350 mA wastes about 3 W, so run LEDs in series to use more of the supply voltage.

A power LED must be mounted on a heatsink. A hot LED loses brightness and life, and its voltage falls as it warms, so a poorly controlled one can run away.

Dimming

PWM dimming switches the current on and off quickly, so the colour stays the same while the brightness changes. Choose a frequency high enough to avoid visible flicker and trouble on camera, often several hundred hertz or more. Analogue dimming lowers the current, which can shift the colour slightly.

Common mistakes
  • Powering a power LED from a fixed voltage with only a resistor.
  • Using a linear driver with a large voltage drop and overheating it.
  • Mounting a power LED with no heatsink.
Key formulas
Rsense = Vref ÷ I
sense resistor of a simple constant-current driver (Vref about 0.6 V for a transistor driver)
P = (Vsupply − Vled) × I
heat a linear driver wastes

Work it with your own numbers: LED resistor

Advanced lesson · Pro plan

Practise this lesson with Pro

The explanation above is free for everyone. The practice for Advanced lessons in every domain are part of the Pro plan at ₹999 a month.

With Pro you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "Constant-Current LED Drivers"?

Drive power LEDs at a steady current using linear and switching drivers, and handle their heat.