Learn / Passive components / Transformers

Transformers and Isolation

ReviewedIntermediate MakerAbout 6 min
In short

Transformers and Isolation: the short answer

A transformer is two coils wound on a shared iron or ferrite core. AC current in the primary coil creates a changing magnetic field in the core, and that field induces a voltage in the secondary coil.

Level
Intermediate
Time
About 6 min
Topic
Passive components
You will learn to

Understand how transformers step AC voltage up or down, why they isolate circuits, and how to use them safely.

Before this: AC, RMS and Real Power, Diodes, LEDs & Polarity

A transformer is two coils wound on a shared iron or ferrite core. AC current in the primary coil creates a changing magnetic field in the core, and that field induces a voltage in the secondary coil. The voltage ratio equals the turns ratio: Vs ÷ Vp = Ns ÷ Np. A 230 V to 12 V mains transformer has about 19 times fewer turns on the secondary. Power in roughly equals power out, so when voltage goes down, current goes up by the same ratio, less a few percent lost as heat.

Transformers only work with changing current. Connect a transformer to DC and the coil behaves like a short circuit through its small wire resistance, overheating quickly. That is why switching power supplies first turn DC into high-frequency AC (tens to hundreds of kilohertz), pass it through a small ferrite transformer, and then rectify it again. Higher frequency allows a much smaller core, which is why a phone charger is tiny compared with an old 50 Hz transformer supply.

The most important property is isolation. The primary and secondary are not connected by any wire, only by the magnetic field, so the low-voltage side is not tied to mains. That is what makes a properly designed charger safe to touch. Isolation is rated in volts (for example 3 kV) and depends on insulation and spacing; never trust a cheap unbranded transformer or an open-frame supply on your bench without a cover. The secondary voltage of a small mains transformer also rises above its label at light load, so a 12 V transformer may give 14 V or more with nothing connected.

Turns ratio sets voltage and current

An ideal transformer changes voltage in proportion to its turns ratio, and current in the inverse proportion, so power stays the same. A 10:1 step-down turns 230 V into 23 V and lets the secondary supply ten times the primary current. It works only with changing current, which is why it needs AC.

The secondary has its own resistance, so the voltage falls as you load it. A small transformer rated 12 V often gives 15 V or more with no load.

Rating and isolation

The rating is in volt-amperes. A 12 V, 12 VA transformer can supply about 1 A. The secondary winding is electrically separate from the mains, which is isolation. That does not make the primary safe to touch; only a properly built, certified mains design does.

After the transformer, a rectifier and a capacitor give DC. The peak of the AC is the RMS value times 1.41, so a 12 V RMS secondary charges the capacitor to about 17 V before the diode drops and the ripple.

Mains work

Treat mains work as a job for a ready-made, enclosed, certified supply. A learner circuit should take its power from a low-voltage adapter or a sealed module, not from an open transformer on the bench.

Common mistakes
  • Using a transformer on DC and expecting an output.
  • Forgetting the peak is 1.41 times the RMS value when choosing the capacitor voltage rating.
  • Building an open mains supply on a breadboard.
Key formulas
Vs ÷ Vp = Ns ÷ Np
voltage follows the turns ratio
Ip × Vp ≈ Is × Vs
power in ≈ power out, so current goes the other way
Intermediate lesson · Maker plan

Practise this lesson with Maker

The explanation above is free for everyone. The practice for Intermediate lessons in every domain are part of the Maker plan at ₹499 a month, and Pro includes them too.

With Maker you also get: a worked example, a hands-on task, a 3-question check.

Common questions

What will I learn in "Transformers and Isolation"?

Understand how transformers step AC voltage up or down, why they isolate circuits, and how to use them safely.