Top 10 mini and final-year electronics projects for ECE and EEE

The 10 best mini and final-year electronics projects for ECE and EEE students: RFID attendance, GSM alert, fingerprint lock, smart cane, solar tracker, gesture robot, irrigation timer and more.

In short

What are the best final-year and mini projects?

Good final-year and mini projects mix a controller, two or three sensors, a clear problem and measurable results. Strong choices from our guided builds are RFID attendance with SD card and RTC, a GSM intruder alert, a fingerprint door lock, a smart cane for blind users, a solar tracker and an energy meter.

Projects
10 guided builds
Levels
Intermediate, Advanced
Build time
1.5 h to 4 h

The 10 projects

These ten are Intermediate or Advanced builds with full guides, so you start with working code and tests and spend your time on upgrades, results and the report. For more, see the final-year briefs.

  1. RFID class attendance with SD card

    Students tap MIFARE cards on an RC522 reader and each tap is saved with date and time to a CSV file the teacher opens in a spreadsheet.

    Intermediate2.5 hSecurityOpen the build →
  2. GSM intruder alert by SMS

    When a PIR sensor sees movement, a SIM800L module sends an SMS to your phone, with a cool-down so you get one message per event.

    Intermediate1.7 hSecurityOpen the build →
  3. Fingerprint door lock

    An R307 fingerprint sensor checks a finger against stored prints and opens a 12 V solenoid lock for the people you enrolled.

    Intermediate2 hSecurityOpen the build →
  4. Smart cane for blind users

    Two ultrasonic sensors on a cane warn of obstacles at waist and head height with vibration that grows stronger as the object gets closer.

    Intermediate3 hAssistive TechOpen the build →
  5. Single-axis solar tracker

    Two LDRs on either side of a divider compare light, and a servo tilts a small solar panel east or west to face the sun.

    Intermediate1.5 hPowerOpen the build →
  6. Hand gesture controlled robot

    Tilt your hand with an MPU6050 glove and an nRF24 link drives a robot car in the direction you tilt.

    Intermediate3 hRoboticsOpen the build →
  7. Drip irrigation timer with zones

    An RTC-based controller opens four 12 V solenoid valves in turn at a set time, so a terrace garden or small farm gets water in the cool morning.

    Intermediate3 hAgricultureOpen the build →
  8. Whole-room energy meter with PZEM-004T

    A PZEM-004T module with a clamp CT measures voltage, current, power and units used by a room, and shows them on a web page.

    Intermediate3 hSmart HomeOpen the build →
  9. Two-wheel self-balancing robot

    An MPU6050 measures the robot's tilt 200 times a second and a PID controller drives two motors to keep it upright.

    Advanced4 hRoboticsOpen the build →
  10. Long-range LoRa sensor link at 866 MHz

    One ESP32 sends BME280 readings over LoRa in India's 865 to 867 MHz band, and a second ESP32 shows them with signal strength on an OLED, often over a kilometre away.

    Advanced2.5 hCommunicationOpen the build →

Before you start

Every build has the full parts list, wiring table, tested code and troubleshooting. Check the circuit or sketch first in the code space or the circuit builder, then order parts with the Buy at Geekobot links on each project page. ElectroLark does not sell parts.

New to the basics? Take the free microcontrollers course, or browse all projects and final-year project briefs.

final-year and mini projects: common questions

How do I choose a final-year electronics project?

Pick a real problem, use two or three sensors, add one feature that is your own and plan to measure results. Check your department's rules before you decide.

Can I copy these projects for my submission?

Use them as a starting point, not a copy. Change the design, add your own upgrade, take your own measurements and write the report in your own words.

Which projects suit ECE and which suit EEE?

ECE: RFID attendance, GSM alert, fingerprint lock, LoRa link. EEE: energy meter, solar tracker, irrigation timer. Robotics builds suit both.

Is there a report template?

The final-year briefs include a block diagram, parts costs, design calculations, tests and a report in the common university layout.

How long does a final-year project take?

The guided builds here take 1.5 to 4 hours to assemble. The rest of the semester goes on upgrades, testing and the report.