Projects / GSM intruder alert by SMS

GSM intruder alert by SMS

Intermediate1.7 hGuided buildReviewed

Build it step by step

0 of 5 done
  1. UNOSIM800LLM2596

    Set the buck converter first

    Power the LM2596 from 12 V, and turn its trimmer until the output reads 4.0 V on a multimeter. Only then connect the SIM800L.

  2. UNODC

    Insert the SIM

    Remove the SIM PIN lock on a phone first. Insert the micro-SIM and screw on the antenna.

  3. UNOSIM800LLM2596

    Wire the GSM

    VCC/GND from the buck with the 1000 µF across them. TXD to D7, D8 to RXD through the divider.

  4. UNO

    Check the network

    Upload and open the serial monitor. AT should reply OK, AT+CSQ a number above 10, and AT+CREG? "0,1" or "0,5".

  5. UNOmotion

    Wire the PIR and test

    PIR OUT to D2. Walk in front of it and wait for the SMS.

In short

How do you build a GSM intruder alert by SMS?

When a PIR sensor sees movement, a SIM800L module sends an SMS to your phone, with a cool-down so you get one message per event. You need Arduino Uno R3, SIM800L GSM module, LM2596 Buck Module, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), Electrolytic capacitor 1000 µF, PIR Motion Sensor HC-SR501, Resistor 1 kΩ, Resistor 2.2 kΩ and Jumper wires male to female (40 pcs). It takes 5 steps and about 100 minutes.

Level
Intermediate
Time
About 100 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapterLM2596 IN+ / IN−Supply for the buck converter
LM2596 OUT+ / OUT− (set to 4.0 V)SIM800L VCC / GNDGSM power, up to 2 A peaks
1000 µFAcross SIM800L VCC and GNDHolds the voltage during transmit bursts
Uno VIN / GND12 V adapter + / −Board power, all grounds joined
SIM800L TXDUno D7Replies from the module
Uno D81 kΩ to SIM800L RXD, 2.2 kΩ from RXD to GNDCommands, divided to about 3 V
PIR OUTUno D2Motion

Code

Arduino IDE, board "Arduino Uno". SoftwareSerial is built in. Put your number with +91 in PHONE. Many Indian operators are switching off 2G, so check your SIM still works on 2G, or use a 4G module (A7670C) with the same AT commands.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <SoftwareSerial.h>

SoftwareSerial gsm(7, 8);          // RX, TX
const char* PHONE = "+91XXXXXXXXXX";
const int PIR = 2;
unsigned long lastSms = 0;
const unsigned long COOLDOWN = 120000;   // at most one SMS every 2 minutes

void at(const char* cmd, int wait = 500) {
  gsm.println(cmd); delay(wait);
  while (gsm.available()) Serial.write(gsm.read());
}

void sendSms(const char* text) {
  at("AT+CMGF=1");                  // text mode
  gsm.print("AT+CMGS=\""); gsm.print(PHONE); gsm.println("\"");
  delay(500);
  gsm.print(text); delay(200);
  gsm.write(26);                    // Ctrl+Z sends the message
  delay(5000);
  while (gsm.available()) Serial.write(gsm.read());
}

void setup() {
  pinMode(PIR, INPUT);
  Serial.begin(9600);
  gsm.begin(9600);
  delay(10000);                     // let the module find the network
  at("AT"); at("AT+CSQ"); at("AT+CREG?");
}

void loop() {
  if (digitalRead(PIR) == HIGH && (lastSms == 0 || millis() - lastSms > COOLDOWN)) {
    Serial.println("Motion: sending SMS");
    sendSms("ElectroLark alert: movement detected at home.");
    lastSms = millis();
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Module LED after 10 to 30 sBlinks every 3 s (registered); every 1 s means still searching
AT+CSQ"+CSQ: 10" to "31"; below 10 is a weak signal
Movement"+CMGS: n" in the monitor and an SMS within 10 s
A second movement within 2 minutesNo second SMS (cool-down)

If it does not work

The module keeps restarting

The supply sags during transmit. Use the 2 A buck converter, short thick wires and the 1000 µF capacitor.

No reply to AT

Swap TX and RX, and check the divider on D8.

Registered but SMS fails

Check SMS balance, the number format and that the operator still runs 2G where you are.

Never power the SIM800L from 5 V

Its maximum is 4.4 V. 5 V can destroy it.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the GSM intruder alert by SMS?

Arduino Uno R3, SIM800L GSM module, LM2596 Buck Module, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), Electrolytic capacitor 1000 µF, PIR Motion Sensor HC-SR501, Resistor 1 kΩ, Resistor 2.2 kΩ and Jumper wires male to female (40 pcs). SIM800L GSM module: Needs a 2G-capable SIM. LM2596 Buck Module: Set to 4.0 V before connecting.

How long does the GSM intruder alert by SMS take to build?

About 100 minutes for a intermediate maker, in 5 steps.

How do I know the GSM intruder alert by SMS works?

Module LED after 10 to 30 s: Blinks every 3 s (registered); every 1 s means still searching. AT+CSQ: "+CSQ: 10" to "31"; below 10 is a weak signal. Movement: "+CMGS: n" in the monitor and an SMS within 10 s.

The module keeps restarting: what should I check?

The supply sags during transmit. Use the 2 A buck converter, short thick wires and the 1000 µF capacitor.

No reply to AT: what should I check?

Swap TX and RX, and check the divider on D8.

Registered but SMS fails: what should I check?

Check SMS balance, the number format and that the operator still runs 2G where you are.

Never power the SIM800L from 5 V: what should I check?

Its maximum is 4.4 V. 5 V can destroy it.