Projects / Drip irrigation timer with zones

Drip irrigation timer with zones

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANOLM2596

    Set the buck output

    Adjust the LM2596 to 5.0 V with a meter before connecting the Nano.

  2. NANOON

    Wire the relays

    Connect the four inputs and the common supply.

  3. NANO

    Add the flyback diodes

    One across each valve, bar to the positive side.

  4. NANO

    Test with one valve

    Run a cycle from the run-now button and listen for the click.

  5. NANODS323110:36

    Set the RTC

    Use a library example sketch once.

  6. NANO

    Set the start time

    Use select and plus buttons for hour, minute and duration.

  7. NANO

    Run all four zones

    Check each valve opens one at a time.

  8. NANO

    Install

    Mount the box away from water and run the pipes.

In short

How do you build a drip irrigation timer with zones?

An RTC-based controller opens four 12 V solenoid valves in turn at a set time, so a terrace garden or small farm gets water in the cool morning. You need Arduino Nano, DS3231 RTC module, Relay module 4-channel 5 V, 12 V solenoid water valve × 4, Rectifier Diode 1N4007 × 4, 12 V 2 A DC adapter, LM2596 Buck Module, 16x2 LCD with I2C backpack (PCF8574) and Tactile push button 6 mm × 3. It takes 8 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapter +LM2596 IN+ and all four relay COM terminalsValve supply and buck input
12 V adapter -LM2596 IN- and all four valve - wiresCommon return
LM2596 OUT+Nano 5V pin and relay module VCCSet to 5.0 V with a meter before connecting
LM2596 OUT-Nano GND and relay module GNDGround
Relay IN1 to IN4Nano D4, D5, D6, D7Zone 1 to 4 control
Relay NO terminals 1 to 4Valve 1 to 4 + wiresSwitched positive
1N4007 diode across each valveCathode (bar) to the + wire, anode to the - wireFlyback protection
DS3231 SDA and SCLNano A4 and A5I2C clock chip
LCD I2C SDA and SCLNano A4 and A5I2C display
DS3231 and LCD VCC and GNDNano 5V and GNDPower
Select buttonNano D8 and GNDChoose the setting to change
Plus buttonNano D9 and GNDIncrease the setting
Run-now buttonNano D10 and GNDStart a cycle now

Code

Each valve is switched by its own relay, and the 1N4007 diode across the valve coil absorbs the voltage spike when the coil switches off, which would otherwise damage the relay contacts and upset the Nano. Zones run one after another so water pressure stays high for each. The start time, minute step and duration are set with the buttons and saved in EEPROM, so they survive a power cut. Use 12 V DC valves rated for the pipe pressure, which is typically very low for gravity-fed drip lines, and keep all electronics in a dry box away from the valves. Mains is only used inside the adapter. Set the DS3231 clock once using an RTClib example sketch. Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Libraries: RTClib (Adafruit), LiquidCrystal_I2C. Runs zones 1 to 4 one after another.
#include <Wire.h>
#include <RTClib.h>
#include <LiquidCrystal_I2C.h>
#include <EEPROM.h>

RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);
const byte ZONES = 4;
const byte RELAY_PIN[ZONES] = {4, 5, 6, 7};
const byte SEL = 8, PLUS = 9, RUNNOW = 10;
const bool ACTIVE_LOW = true;                 // most relay boards turn on with LOW

byte startHour = 6, startMin = 0, durMin = 10;   // saved in EEPROM
byte field = 0;                                // 0 hour, 1 minute, 2 duration
bool running = false;
byte zone = 0;
unsigned long zoneStart = 0;
byte lastRunDay = 255;

void relay(byte z, bool on) { digitalWrite(RELAY_PIN[z], (on == ACTIVE_LOW) ? LOW : HIGH); }
void allOff() { for (byte z = 0; z < ZONES; z++) relay(z, false); }

bool pressed(byte pin) {
  static unsigned long last[16];
  if (digitalRead(pin) == LOW && millis() - last[pin] > 250) { last[pin] = millis(); return true; }
  return false;
}

void startCycle() { running = true; zone = 0; zoneStart = millis(); allOff(); relay(0, true); }

void setup() {
  for (byte z = 0; z < ZONES; z++) { pinMode(RELAY_PIN[z], OUTPUT); }
  allOff();
  pinMode(SEL, INPUT_PULLUP); pinMode(PLUS, INPUT_PULLUP); pinMode(RUNNOW, INPUT_PULLUP);
  lcd.init(); lcd.backlight();
  rtc.begin();
  byte h = EEPROM.read(0), m = EEPROM.read(1), d = EEPROM.read(2);
  if (h < 24 && m < 60 && d >= 1 && d <= 60) { startHour = h; startMin = m; durMin = d; }
}

void loop() {
  DateTime now = rtc.now();

  if (pressed(SEL)) field = (field + 1) % 3;
  if (pressed(PLUS)) {
    if (field == 0) startHour = (startHour + 1) % 24;
    if (field == 1) startMin = (startMin + 5) % 60;
    if (field == 2) durMin = (durMin % 60) + 1;
    EEPROM.update(0, startHour); EEPROM.update(1, startMin); EEPROM.update(2, durMin);
  }
  if (pressed(RUNNOW) && !running) startCycle();

  // Start once per day at the set time
  if (!running && now.hour() == startHour && now.minute() == startMin && now.day() != lastRunDay) {
    lastRunDay = now.day();
    startCycle();
  }

  // One zone at a time so pressure stays up
  if (running && millis() - zoneStart >= (unsigned long)durMin * 60000UL) {
    relay(zone, false);
    zone++;
    if (zone >= ZONES) { running = false; }
    else { relay(zone, true); zoneStart = millis(); }
  }

  lcd.setCursor(0, 0);
  char l0[17];
  sprintf(l0, "%02d:%02d  Start %02d:%02d", now.hour(), now.minute(), startHour, startMin);
  lcd.print(l0);
  lcd.setCursor(0, 1);
  char l1[17];
  if (running) sprintf(l1, "Zone %d running  ", zone + 1);
  else sprintf(l1, "Dur %2d min %c     ", durMin, "HMD"[field]);
  lcd.print(l1);
  delay(100);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Run nowZones run one after another
At the start timeCycle starts once that day
Power cut and restartSettings remembered
Diode removed in testMore relay noise, so keep it fitted

If it does not work

Relay does not click

Check the logic (ACTIVE_LOW) and the 5 V supply.

Valve does not open

Check the 12 V on the COM terminal and the NO wiring.

Nano resets

Check the flyback diodes and the buck output.

Wrong time

Set the RTC again and check the battery on it.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the drip irrigation timer with zones?

Arduino Nano, DS3231 RTC module, Relay module 4-channel 5 V, 12 V solenoid water valve × 4, Rectifier Diode 1N4007 × 4, 12 V 2 A DC adapter, LM2596 Buck Module, 16x2 LCD with I2C backpack (PCF8574) and Tactile push button 6 mm × 3.

How long does the drip irrigation timer with zones take to build?

About 180 minutes for a intermediate maker, in 8 steps.

How do I know the drip irrigation timer with zones works?

Run now: Zones run one after another. At the start time: Cycle starts once that day. Power cut and restart: Settings remembered.

Relay does not click: what should I check?

Check the logic (ACTIVE_LOW) and the 5 V supply.

Valve does not open: what should I check?

Check the 12 V on the COM terminal and the NO wiring.

Nano resets: what should I check?

Check the flyback diodes and the buck output.

Wrong time: what should I check?

Set the RTC again and check the battery on it.