Projects / RFID class attendance with SD card

RFID class attendance with SD card

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. UNORC522

    Test the reader

    Print UIDs.

  2. UNOMICROS

    Test the SD card

    Write a line.

  3. UNODS323113:39

    Set the RTC

    Check the time shows.

  4. UNO

    Make roll.csv

    UID and name per line.

  5. UNOHelloPCF8574

    Match a tap to a name

    Show it on the LCD.

  6. UNO

    Log to attendance.csv

    Date, time, UID and name.

  7. UNO

    Add the 10 minute rule

    Ignore repeats.

In short

How do you build an RFID class attendance with SD card?

Students tap MIFARE cards on an RC522 reader and each tap is saved with date and time to a CSV file the teacher opens in a spreadsheet. You need Arduino Uno R3, RC522 RFID reader, RFID tags 13.56 MHz (MIFARE Classic 1K) × 10, DS3231 RTC module, MicroSD Card Module, 16x2 LCD with I2C backpack (PCF8574) and Active buzzer 5 V. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
RC522 SDA (SS)Uno D10Reader chip select
SD module CSUno D4Card chip select
RC522 and SD SCK, MOSI, MISOUno D13, D11, D12Shared SPI bus
RC522 RSTUno D9Reset
RC522 3.3V and GNDUno 3.3V and GNDPower (never 5 V)
SD module VCC and GNDUno 5V and GNDPower
RTC and LCD SDA, SCLUno A4, A5Shared I2C bus
RTC and LCD VCC, GNDUno 5V, GNDPower
Buzzer plus and minusUno D8 and GNDBeep

Code

Each card has a unique number, the UID, which the reader can read in a moment. The sketch looks that number up in a list on the SD card to find the name, then adds a line with the date and time to a CSV file that opens in any spreadsheet. A second tap within ten minutes is ignored, so a student cannot be counted twice by accident. The reader and the SD card share the same three SPI wires and each has its own chip-select wire, so only one listens at a time. Because the roll list holds names, keep to your school's rules on student data: tell students what is recorded, store only what you need, and keep the card in a safe place. A card's number can be copied, so this is a convenience for marking attendance and not proof of identity; for anything that matters, the teacher should still check. Set the RTC once and fit its coin cell, so the time survives a power cut. Arduino IDE, board "Arduino Uno".

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// RFID class attendance: a tap is matched to roll.csv on the SD card and logged to attendance.csv with date and time.
// roll.csv has one line per card: UID in capital hex with no spaces, a comma, then the name (for example 04A1B2C3,Asha).
// Libraries: MFRC522, SD, RTClib, LiquidCrystal_I2C. Board: Arduino Uno.
#include <SPI.h>
#include <SD.h>
#include <MFRC522.h>
#include <RTClib.h>
#include <LiquidCrystal_I2C.h>
MFRC522 rfid(10, 9);
RTC_DS3231 rtc;
LiquidCrystal_I2C lcd(0x27, 16, 2);
const byte SD_CS = 4;
const unsigned long REPEAT_MS = 600000UL;      // ignore a second tap within 10 minutes
String lastUid[8]; unsigned long lastTime[8]; byte nLast = 0;
String uidString() {
  String s;
  for (byte i = 0; i < rfid.uid.size; i++) { if (rfid.uid.uidByte[i] < 0x10) s += "0"; s += String(rfid.uid.uidByte[i], HEX); }
  s.toUpperCase(); return s;
}
String findName(const String& uid) {
  File f = SD.open("roll.csv");
  String name = "";
  while (f && f.available()) {
    String line = f.readStringUntil('\n'); line.trim();
    int c = line.indexOf(',');
    if (c > 0 && line.substring(0, c) == uid) { name = line.substring(c + 1); break; }
  }
  if (f) f.close();
  return name;
}
bool recentlySeen(const String& uid) {
  for (byte i = 0; i < nLast; i++) if (lastUid[i] == uid) { if (millis() - lastTime[i] < REPEAT_MS) return true; lastTime[i] = millis(); return false; }
  if (nLast < 8) { lastUid[nLast] = uid; lastTime[nLast] = millis(); nLast++; }
  return false;
}
void show(const String& a, const String& b) { lcd.clear(); lcd.print(a); lcd.setCursor(0, 1); lcd.print(b); }
void setup() {
  SPI.begin();
  pinMode(8, OUTPUT); pinMode(SD_CS, OUTPUT); digitalWrite(SD_CS, HIGH);
  rfid.PCD_Init();
  lcd.init(); lcd.backlight();
  rtc.begin();
  if (!SD.begin(SD_CS)) { show("SD card error", ""); while (true) {} }
  show("Tap your card", "");
}
void loop() {
  if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) return;
  String uid = uidString();
  String name = findName(uid);
  if (name == "") { show("Unknown card", uid); tone(8, 300, 500); }
  else if (recentlySeen(uid)) { show(name, "already marked"); tone(8, 600, 200); }
  else {
    DateTime n = rtc.now();
    File f = SD.open("attendance.csv", FILE_WRITE);
    if (f) {
      char line[64];
      snprintf(line, sizeof(line), "%04d-%02d-%02d,%02d:%02d:%02d,", n.year(), n.month(), n.day(), n.hour(), n.minute(), n.second());
      f.print(line); f.print(uid); f.print(','); f.println(name); f.close();
      show(name, "marked present"); tone(8, 1500, 150);
    } else show("Write error", "");
  }
  rfid.PICC_HaltA();
  delay(1200);
  show("Tap your card", "");
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Known cardName shown, marked present
Same card againAlready marked
Unknown cardMessage and low beep
CSV fileOpens with correct times

If it does not work

SD error

Format as FAT32 and check the chip select.

Reader not found

Check 3.3 V and the SS wire.

Wrong time

Set the RTC from the example sketch.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the RFID class attendance with SD card?

Arduino Uno R3, RC522 RFID reader, RFID tags 13.56 MHz (MIFARE Classic 1K) × 10, DS3231 RTC module, MicroSD Card Module, 16x2 LCD with I2C backpack (PCF8574) and Active buzzer 5 V.

How long does the RFID class attendance with SD card take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the RFID class attendance with SD card works?

Known card: Name shown, marked present. Same card again: Already marked. Unknown card: Message and low beep.

SD error: what should I check?

Format as FAT32 and check the chip select.

Reader not found: what should I check?

Check 3.3 V and the SS wire.

Wrong time: what should I check?

Set the RTC from the example sketch.