Projects / Long-range LoRa sensor link at 866 MHz

Long-range LoRa sensor link at 866 MHz

Advanced2.5 hGuided buildReviewed

Build it step by step

0 of 5 done
  1. ESP32RFM95W868

    Fit the antennas first

    Solder or screw an 868 MHz antenna to each RFM95W. Transmitting without one can damage the radio.

  2. ESP32

    Wire both radios

    3V3, GND, SCK 18, MISO 19, MOSI 23, NSS 5, RESET 14, DIO0 2.

  3. ESP32BME28024.0°C

    Build the sender

    BME280 on GPIO21/22. Upload with SENDER 1.

  4. ESP3212.0 mASSD1306

    Build the receiver

    OLED on GPIO21/22. Upload with SENDER 0.

  5. ESP32

    Range test

    Put the sender high up (a terrace) and walk or ride away with the receiver on a power bank, noting RSSI and where packets stop.

In short

How do you build a long-range LoRa sensor link at 866 MHz?

One ESP32 sends BME280 readings over LoRa in India's 865 to 867 MHz band, and a second ESP32 shows them with signal strength on an OLED, often over a kilometre away. You need ESP32 DevKit V1 × 2, RFM95W LoRa module (868 MHz) × 2, 868 MHz LoRa antenna × 2, BME280 Environmental Sensor, SSD1306 OLED Display, USB A to micro-USB cable (data) × 2 and Jumper wires female to female (40 pcs). It takes 5 steps and about 150 minutes.

Level
Advanced
Time
About 150 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
RFM95W 3.3V / GNDESP32 3V3 / GNDRadio power (both boards)
RFM95W SCK / MISO / MOSIESP32 GPIO18 / GPIO19 / GPIO23SPI
RFM95W NSS / RESET / DIO0ESP32 GPIO5 / GPIO14 / GPIO2Chip select, reset, packet interrupt
RFM95W ANT868 MHz antennaNever transmit without an antenna
Sender: BME280 SDA / SCLGPIO21 / GPIO22Sensor
Receiver: OLED SDA / SCLGPIO21 / GPIO22Display

Code

Arduino IDE with the ESP32 board package (Espressif), board "ESP32 Dev Module". Install "LoRa" by Sandeep Mistry, "Adafruit BME280" and "Adafruit SSD1306". 865 to 867 MHz is licence-exempt for low-power devices in India; keep to it.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#define SENDER 1           // 1 = sensor node, 0 = receiver with OLED
#include <SPI.h>
#include <LoRa.h>
#include <Wire.h>

void radio() {
  LoRa.setPins(5, 14, 2);  // NSS, RESET, DIO0
  if (!LoRa.begin(866E6)) { Serial.println("LoRa not found"); while (true) delay(100); }
  LoRa.setSpreadingFactor(9);      // longer range than the default 7, slower
  LoRa.setSignalBandwidth(125E3);
  LoRa.setSyncWord(0x5A);          // only talk to our own nodes
  LoRa.enableCrc();
}

#if SENDER
#include <Adafruit_BME280.h>
Adafruit_BME280 bme;
int count = 0;
void setup() { Serial.begin(115200); bme.begin(0x76); radio(); }
void loop() {
  String msg = String(count++) + "," + String(bme.readTemperature(), 1) + "," + String(bme.readHumidity(), 0) + "," + String(bme.readPressure() / 100, 0);
  LoRa.beginPacket(); LoRa.print(msg); LoRa.endPacket();
  Serial.println("Sent " + msg);
  delay(15000);
}
#else
#include <Adafruit_SSD1306.h>
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
void setup() {
  Serial.begin(115200); radio();
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C); oled.setTextColor(SSD1306_WHITE);
}
void loop() {
  if (!LoRa.parsePacket()) return;
  String msg; while (LoRa.available()) msg += (char)LoRa.read();
  int rssi = LoRa.packetRssi(); float snr = LoRa.packetSnr();
  Serial.printf("%s  RSSI %d dBm  SNR %.1f dB\n", msg.c_str(), rssi, snr);
  int a = msg.indexOf(','), b = msg.indexOf(',', a + 1), c = msg.indexOf(',', b + 1);
  oled.clearDisplay(); oled.setCursor(0, 0);
  oled.printf("Packet #%s\n\n", msg.substring(0, a).c_str());
  oled.printf("Temp  %s C\nHum   %s %%\nPress %s hPa\n\n", msg.substring(a + 1, b).c_str(), msg.substring(b + 1, c).c_str(), msg.substring(c + 1).c_str());
  oled.printf("RSSI %d  SNR %.1f", rssi, snr);
  oled.display();
}
#endif

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Same roomPackets every 15 s, RSSI about −30 to −60 dBm, SNR above +8 dB
Packet numberGoes up by one each time; gaps mean lost packets
Edge of rangeRSSI near −120 dBm and SNR below −10 dB before packets stop
Open line of sight with the sender on a roofOften 1 to 3 km at SF9

If it does not work

"LoRa not found"

Check NSS, RESET and the SPI wires. The RFM95W is 3.3 V only.

Nothing received

Both sides must use the same frequency, spreading factor, bandwidth and sync word.

Short range

Raise the antennas, keep them vertical and away from metal, or try SF10 to SF12 (slower but longer).

Legal use

Stay in 865 to 867 MHz and send short packets with gaps, as here.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the long-range LoRa sensor link at 866 MHz?

ESP32 DevKit V1 × 2, RFM95W LoRa module (868 MHz) × 2, 868 MHz LoRa antenna × 2, BME280 Environmental Sensor, SSD1306 OLED Display, USB A to micro-USB cable (data) × 2 and Jumper wires female to female (40 pcs). RFM95W LoRa module (868 MHz) × 2: 868 MHz modules tune to 866 MHz.

How long does the long-range LoRa sensor link at 866 MHz take to build?

About 150 minutes for a advanced maker, in 5 steps.

How do I know the long-range LoRa sensor link at 866 MHz works?

Same room: Packets every 15 s, RSSI about −30 to −60 dBm, SNR above +8 dB. Packet number: Goes up by one each time; gaps mean lost packets. Edge of range: RSSI near −120 dBm and SNR below −10 dB before packets stop.

LoRa not found: what should I check?

Check NSS, RESET and the SPI wires. The RFM95W is 3.3 V only.

Nothing received: what should I check?

Both sides must use the same frequency, spreading factor, bandwidth and sync word.

Short range: what should I check?

Raise the antennas, keep them vertical and away from metal, or try SF10 to SF12 (slower but longer).

Legal use: what should I check?

Stay in 865 to 867 MHz and send short packets with gaps, as here.