Projects / Smart cane for blind users

Smart cane for blind users

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANOMT3608

    Set the boost module

    Adjust to 5.0 V with no load.

  2. NANO

    Wire the Nano and sensors

    On a breadboard first.

  3. NANOBC547

    Wire the motors with transistors

    Diodes across the motors.

  4. NANO

    Upload and bench test

    Hand in front of each sensor.

  5. NANO

    Check the vibration feel

    Strong when close, none beyond 150 cm.

  6. NANO

    Mount on a cane

    Angles as described.

  7. NANO

    Test outdoors in a safe place

    With a helper.

  8. NANO

    Ask the user for feedback

    Adjust distances and strength.

In short

How do you build a smart cane for blind users?

Two ultrasonic sensors on a cane warn of obstacles at waist and head height with vibration that grows stronger as the object gets closer. You need Arduino Nano, HC-SR04 Ultrasonic Sensor × 2, Vibration motor (coin type) × 2, BC547 NPN transistor × 2, Resistor 1 kΩ × 2, Signal Diode 1N4148 × 2, 18650 cell 2600 mAh (branded), Battery holder 18650 single, TP4056 module with protection (USB-C), MT3608 Boost Module and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
11

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Low HC-SR04 VCC, GND5 V rail and GNDSensor pointing forward and slightly down
Low HC-SR04 TRIG, ECHONano D2, D3Waist-level obstacles
High HC-SR04 VCC, GND5 V rail and GNDSensor pointing forward and up
High HC-SR04 TRIG, ECHONano D4, D5Head-level obstacles
Nano D91 k to BC547 base, emitter to GNDLow-sensor motor driver
Nano D101 k to BC547 base, emitter to GNDHigh-sensor motor driver
Each coin motorPlus to the 5 V rail, minus to its BC547 collector, 1N4148 across the motor (stripe to plus)Vibration
18650 holderTP4056 module with protection B+ and B-Charging and cell protection
TP4056 OUT+ and OUT-MT3608 IN+ and IN-Boost input
MT3608 OUTNano 5V pin and the 5 V rail, set to 5.0 V before connectingRegulated 5 V

Code

Each HC-SR04 sends a burst of sound and times the echo; distance in centimetres is the echo time in microseconds divided by 58. One sensor points forward and slightly down to catch things at waist level and the other points up for head-height hazards such as low branches. The two are read one after the other with a short pause, because their pings could confuse each other. Each distance becomes a vibration strength, stronger as the object gets closer, and the two sensors feel different: waist level is a steady buzz and head level is pulsing, so the user can tell them apart without looking. Coin motors are driven through BC547 transistors, with a 1N4148 diode across each motor to absorb the voltage spike when it switches off. The cane is powered by a single 18650 cell on a protected TP4056 module, boosted to 5 V by an MT3608. Turn the MT3608's trimmer to read exactly 5.0 V on a multimeter before you connect the Nano, because many modules ship at a higher voltage that would damage it. Never charge the cell unattended, and use a protected cell and the protected module only. Ultrasonic sensors miss thin poles, soft clothing and steps down, so this device warns of some obstacles only; it is an extra aid and must not replace a white cane or training. Test it first with a sighted helper in a safe open space, then with the actual users and ask for their feedback. Setup: Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Obstacle warning cane. An aid, never a replacement for a white cane or other mobility training.
const uint8_t TRIG_LOW = 2, ECHO_LOW = 3, TRIG_HIGH = 4, ECHO_HIGH = 5;
const uint8_t MOTOR_LOW = 9, MOTOR_HIGH = 10;
const int NEAR_CM = 20, FAR_CM = 150;          // vibration starts at 150 cm and is strongest at 20 cm
const uint8_t MAX_PWM = 170;                   // about 67 percent, keeps a 3 V coin motor safe

int readCm(uint8_t trig, uint8_t echo) {
  digitalWrite(trig, LOW);  delayMicroseconds(2);
  digitalWrite(trig, HIGH); delayMicroseconds(10);
  digitalWrite(trig, LOW);
  unsigned long us = pulseIn(echo, HIGH, 12000UL);  // give up after about 2 m
  if (us == 0) return 999;                           // nothing seen
  return us / 58;
}

uint8_t strength(int cm) {
  if (cm >= FAR_CM) return 0;
  if (cm <= NEAR_CM) return MAX_PWM;
  return map(cm, FAR_CM, NEAR_CM, 30, MAX_PWM);
}

void setup() {
  pinMode(TRIG_LOW, OUTPUT);  pinMode(ECHO_LOW, INPUT);
  pinMode(TRIG_HIGH, OUTPUT); pinMode(ECHO_HIGH, INPUT);
  pinMode(MOTOR_LOW, OUTPUT); pinMode(MOTOR_HIGH, OUTPUT);
}

void loop() {
  int low = readCm(TRIG_LOW, ECHO_LOW);
  delay(30);                                       // let the first echo die before the second ping
  int high = readCm(TRIG_HIGH, ECHO_HIGH);

  analogWrite(MOTOR_LOW, strength(low));           // steady buzz for waist level
  bool pulse = (millis() / 120) % 2;               // pulsing buzz for head level
  analogWrite(MOTOR_HIGH, pulse ? strength(high) : 0);
  delay(30);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hand at 100 cm in front of the low sensorGentle steady vibration
Hand at 20 cmStrongest steady vibration
Hand in front of the high sensorPulsing vibration
Nothing in frontNo vibration
Run for ten minutesNothing gets hot

If it does not work

Constant vibration

Sensors seeing each other or a cane edge; adjust the angle.

No vibration

Check the transistor pins (E, B, C) and diode direction.

Nano resets when motors start

Boost module too weak or loose wire; add a 100 uF capacitor on 5 V.

Readings jump

Soft objects and angles confuse ultrasound.

Cell drains quickly

Motors at full strength; lower MAX_PWM.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the smart cane for blind users?

Arduino Nano, HC-SR04 Ultrasonic Sensor × 2, Vibration motor (coin type) × 2, BC547 NPN transistor × 2, Resistor 1 kΩ × 2, Signal Diode 1N4148 × 2, 18650 cell 2600 mAh (branded), Battery holder 18650 single, TP4056 module with protection (USB-C), MT3608 Boost Module and Jumper wires male to male (40 pcs, 20 cm).

How long does the smart cane for blind users take to build?

About 180 minutes for a intermediate maker, in 8 steps.

How do I know the smart cane for blind users works?

Hand at 100 cm in front of the low sensor: Gentle steady vibration. Hand at 20 cm: Strongest steady vibration. Hand in front of the high sensor: Pulsing vibration.

Constant vibration: what should I check?

Sensors seeing each other or a cane edge; adjust the angle.

No vibration: what should I check?

Check the transistor pins (E, B, C) and diode direction.

Nano resets when motors start: what should I check?

Boost module too weak or loose wire; add a 100 uF capacitor on 5 V.

Readings jump: what should I check?

Soft objects and angles confuse ultrasound.