CMOS 555 against bipolar 555
Build it step by step
0 of 8 doneBuild the NE555 blinker
R1 10k, R2 100k, 10 uF, LED through 1k.
Check the blink
About once every 1.5 seconds.
Measure the supply current
Meter in series, LED unplugged.
Add diodes
Insert 1N4148 diodes one at a time in the supply.
Note where it stops
Write down the supply at the chip.
Build the TLC555 version
Same parts, same pinout.
Repeat the tests
Current and diode steps.
Compare
Complete the table.
How do you build a CMOS 555 against bipolar 555?
Run the same blinker on both timer types and compare supply current and the lowest working voltage. You need TLC555 CMOS timer, NE555 Timer IC, Resistor 10 kΩ × 2, Resistor 100 kΩ × 2, Electrolytic capacitor 10 µF × 2, Ceramic Capacitor 100 nF × 2, LED 5 mm red × 2, Resistor 1 kΩ × 2, Signal Diode 1N4148 × 4, Digital multimeter, 5 V 2 A USB adapter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 90 minutes.
- Level
- Beginner
- Time
- About 90 min
- Parts
- 13
Parts list
- Integrated CircuitsBuy
- Integrated CircuitsBuyNE555 Timer IC × 1
- PassivesBuyResistor 10 kΩ × 2
- PassivesBuyResistor 100 kΩ × 2
- PassivesBuy
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 2
- PassivesBuyResistor 1 kΩ × 2
- SemiconductorsBuy
- Tools & InstrumentsBuy
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 5 V adapter positive | Red rail (through the multimeter for current tests) | Supply |
| 5 V adapter negative | Blue rail | Ground |
| 555 pin 8 (VCC) and pin 4 (RESET) | Red rail | Power and reset held high |
| 555 pin 1 (GND) | Blue rail | Ground |
| 10 kilohm resistor | Red rail to pin 7 (DISCH) | R1 |
| 100 kilohm resistor | Pin 7 to pins 6 and 2 (THRESH and TRIG, joined) | R2 |
| 10 uF capacitor | Pins 6 and 2 to GND, plus leg toward pin 2 | Timing capacitor |
| 100 nF capacitor | Pin 5 (CONTROL) to GND | Noise filter |
| LED cathode | Pin 3 (OUT) | Lit when the output is low |
| LED anode | 1 kilohm to the red rail | Current limit |
| Series 1N4148 diodes (banded ends toward the chip) | In the supply line to the chip | Each one drops about 0.7 V |
Code
The NE555 timer from 1971 is one of the best selling chips ever, and the CMOS version, the TLC555, does the same job on a fraction of the power. This lab puts them side by side on the same 5 volt supply with the same resistors and capacitor, so any difference you measure comes from the chip. Both blink about once every one and a half seconds, and the formula for the frequency is identical, which is why one is a drop-in replacement for the other in most circuits. The first difference is supply current. The bipolar NE555 draws several milliamps just sitting there, while the CMOS part draws a few hundred microamps, which is why battery-powered designs prefer it. Measure with the meter in series with the supply and the LED disconnected, since the LED current would hide the chip current. The second difference is the lowest working voltage. The NE555 is specified for 4.5 volts or more, while the TLC555 works from 2 volts. A few 1N4148 diodes in series with the supply drop the voltage in steps of about 0.7 volts, so you can see where each chip stops blinking. Treat the datasheet figures as guidance, because real parts often go a little lower than they are specified, and temperature, supplier and age all change the result.
Build notes (no code needed for this build) Build the same astable twice, once with the TLC555 (CMOS) and once with the NE555 (bipolar), on the same 5 V supply. 555 pins (DIP-8): 1 GND, 2 TRIG, 3 OUT, 4 RESET, 5 CONTROL, 6 THRESH, 7 DISCH, 8 VCC. Timing: R1 = 10 kilohm, R2 = 100 kilohm, C = 10 uF. Frequency = 1.44 / ((R1 + 2 x R2) x C) = 1.44 / (210 kilohm x 10 uF) = about 0.69 Hz, a visible blink for both chips. (Real values vary with the capacitor tolerance, which can be 20 percent for an electrolytic.) 1. Supply current: put the multimeter in series with the supply, with the LED disconnected so you measure only the chip. Expect (from datasheets, 5 V): NE555 about 3 to 6 mA, TLC555 about 0.1 to 0.3 mA, so the CMOS part uses roughly twenty times less. 2. Lowest working voltage: place 1N4148 diodes in series in the supply line to the chip, one at a time, and note how many the blinker survives. Each diode drops about 0.7 V, so 5 V gives about 4.3, 3.6, 2.9 and 2.2 V at the chip. The NE555 is specified from 4.5 V and usually stops somewhere around 3 to 4.5 V, while the TLC555 is specified from 2 V and keeps running to about 2 to 3 V. 3. Change R2 or C and note that both chips follow the same formula. Record in a table: chip, supply voltage at the chip, blink or not, current in mA. The CMOS part is sensitive to static and has a lower output current, so keep the LED current small (1 kilohm, about 2 mA).
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Blink rate | About 0.7 Hz for both |
| NE555 current | About 3 to 6 mA |
| TLC555 current | About 0.1 to 0.3 mA |
| NE555 stops | Roughly between 3 and 4.5 V |
| TLC555 stops | Roughly between 2 and 3 V |
If it does not work
No blink
Check pin 4 is on the rail and pins 2 and 6 are joined.
Blink too fast
Check the 10 uF capacitor value and polarity.
Current looks high
Disconnect the LED when measuring the chip.
Meter reads zero
Check the red lead is in the mA jack for current.
Readings jump
Add the 100 nF capacitor on pin 5.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the CMOS 555 against bipolar 555?
TLC555 CMOS timer, NE555 Timer IC, Resistor 10 kΩ × 2, Resistor 100 kΩ × 2, Electrolytic capacitor 10 µF × 2, Ceramic Capacitor 100 nF × 2, LED 5 mm red × 2, Resistor 1 kΩ × 2, Signal Diode 1N4148 × 4, Digital multimeter, 5 V 2 A USB adapter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.
How long does the CMOS 555 against bipolar 555 take to build?
About 90 minutes for a beginner maker, in 8 steps.
How do I know the CMOS 555 against bipolar 555 works?
Blink rate: About 0.7 Hz for both. NE555 current: About 3 to 6 mA. TLC555 current: About 0.1 to 0.3 mA.
No blink: what should I check?
Check pin 4 is on the rail and pins 2 and 6 are joined.
Blink too fast: what should I check?
Check the 10 uF capacitor value and polarity.
Current looks high: what should I check?
Disconnect the LED when measuring the chip.
Meter reads zero: what should I check?
Check the red lead is in the mA jack for current.
