Projects / Fault-finding challenge

Fault-finding challenge

Intermediate45 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO13.4 mA

    Build the working circuit

    Check all three LEDs and the button.

  2. NANO

    Photograph it

    A reference for later.

  3. NANO

    Close your eyes

    Partner adds one fault.

  4. NANO

    Check power first

    Rail voltage and ground.

  5. NANO

    Halve the circuit

    Test the middle point.

  6. NANO

    Find and fix the fault

    One wire or part.

  7. NANO

    Explain the cause

    Write down what you saw on the meter.

In short

How do you build a fault-finding challenge?

A partner breaks a working circuit in one hidden way and you find the fault with a meter. You need Digital multimeter, Arduino Nano, LED 5 mm red × 3, Resistor 220 Ω × 3, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 45 minutes.

Level
Intermediate
Time
About 45 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Nano D2, D3, D4220 Ω, then red LED to groundThree LEDs
ButtonNano D5 and ground (internal pull-up)Pattern button
Nano 5V and GNDBreadboard railsPower
Fault cardOne of the faults in the notesChosen by your partner

Code

Build the circuit and check it works while your partner looks away, then your partner adds exactly one fault while you are out of the room: swap one LED round, leave a resistor out, move a jumper one hole, lift a ground wire, put a resistor on the wrong row, or move the button to a different pin. Find the fault the way a technician does. Check power first: is 5 V present at the rails and is ground connected? Then halve the circuit, testing in the middle, to find which half has the fault, and keep halving until you find one wire or part. Use the meter to measure instead of guessing: voltage across each LED, and continuity of each wire with the power off. Write down what you measured and what you found. Swap roles and try again. Work with the Nano on its USB cable only and never test mains circuits this way. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Known-good circuit: each button press lights the next LED, so every part of the circuit gets used. Board: Arduino Nano.
const int LEDS[3] = {2, 3, 4};
const int BTN = 5;
int idx = 0;
void setup() {
  for (int i = 0; i < 3; i++) pinMode(LEDS[i], OUTPUT);
  pinMode(BTN, INPUT_PULLUP);
  digitalWrite(LEDS[0], HIGH);
}
void loop() {
  if (digitalRead(BTN) == LOW) {
    digitalWrite(LEDS[idx], LOW);
    idx = (idx + 1) % 3;
    digitalWrite(LEDS[idx], HIGH);
    delay(300);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Working circuitLEDs step on each press
With the faultSymptom is clear but the cause is hidden
Fault found in under 10 minutesUsing the meter, not guessing
FixedBack to normal

If it does not work

Cannot find it

Go back to the power check.

Meter shows nothing

Check the range and the probes.

Two faults

Fix one first, then retest.

Partner cheats

Agree one fault only.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the fault-finding challenge?

Digital multimeter, Arduino Nano, LED 5 mm red × 3, Resistor 220 Ω × 3, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the fault-finding challenge take to build?

About 45 minutes for a intermediate maker, in 7 steps.

How do I know the fault-finding challenge works?

Working circuit: LEDs step on each press. With the fault: Symptom is clear but the cause is hidden. Fault found in under 10 minutes: Using the meter, not guessing.

Cannot find it: what should I check?

Go back to the power check.

Meter shows nothing: what should I check?

Check the range and the probes.

Two faults: what should I check?

Fix one first, then retest.

Partner cheats: what should I check?

Agree one fault only.