Build it step by step
0 of 5 doneFind the keypad pins
The 8-pin ribbon is rows 1-4 then columns 1-4, left to right with the keys facing you. Wire them to D9 down to D2.
Wire the LCD
SDA to A4, SCL to A5, VCC and GND.
Wire the lock side
12 V plus to relay COM, NO to solenoid plus, solenoid minus to 12 V minus. Fit the 1N4007 across the solenoid, stripe to plus.
Relay and buzzer
Relay IN to A0, buzzer to A1.
Upload and test on the bench
Type 1234 then #. The solenoid should pull in for 5 s. Then change the code in the sketch.
How do you build a keypad password door lock?
Enter a 4-digit code on a membrane keypad and a 12 V solenoid lock opens for five seconds, with prompts on an LCD. You need Arduino Uno R3, 4x4 matrix keypad (membrane), 16x2 LCD with I2C backpack (PCF8574), Relay Module 5V, Solenoid lock 12 V, Rectifier Diode 1N4007, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), Active buzzer 5 V and Jumper wires male to male (40 pcs, 20 cm). It takes 5 steps and about 100 minutes.
- Level
- Intermediate
- Time
- About 100 min
- Parts
- 10
Parts list
- Development BoardsBuyArduino Uno R3 × 1
- SwitchesBuy
- DisplaysBuy
- InterfacesBuyRelay Module 5V × 1
- Motors & ActuatorsBuy
- SemiconductorsBuyAcross the solenoid, stripe to plus
- PowerBuy
- PowerBuy
- Motors & ActuatorsBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Keypad rows 1-4 | Uno D9, D8, D7, D6 | Row lines |
| Keypad columns 1-4 | Uno D5, D4, D3, D2 | Column lines |
| LCD SDA / SCL / VCC / GND | Uno A4 / A5 / 5V / GND | Prompts |
| Relay IN / VCC / GND | Uno A0 / 5V / GND | Lock control (A0 used as a digital pin) |
| 12 V + | Relay COM; relay NO to solenoid + | Solenoid power through the relay |
| Solenoid − | 12 V − | Return |
| 1N4007 | Across the solenoid, stripe to + | Absorbs the coil's voltage spike |
| Uno A1 | Buzzer + (− to GND) | Key beeps and wrong-code alarm |
Code
Arduino IDE, board "Arduino Uno". Install Keypad (Mark Stanley, Alexander Brevig) and LiquidCrystal I2C. Change "1234" before use. Press # to enter and * to clear.
Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
#include <Keypad.h>
#include <LiquidCrystal_I2C.h>
const char KEYS[4][4] = {{'1','2','3','A'},{'4','5','6','B'},{'7','8','9','C'},{'*','0','#','D'}};
byte rows[4] = {9, 8, 7, 6}, cols[4] = {5, 4, 3, 2};
Keypad pad = Keypad(makeKeymap(KEYS), rows, cols, 4, 4);
LiquidCrystal_I2C lcd(0x27, 16, 2);
const int RELAY = A0, BUZZER = A1;
const bool ON = LOW;
String code = "1234", entry = "";
int wrong = 0;
void prompt() { lcd.clear(); lcd.print("Enter code:"); lcd.setCursor(0, 1); entry = ""; }
void beep(int ms) { digitalWrite(BUZZER, HIGH); delay(ms); digitalWrite(BUZZER, LOW); }
void setup() {
pinMode(RELAY, OUTPUT); digitalWrite(RELAY, !ON);
pinMode(BUZZER, OUTPUT);
lcd.init(); lcd.backlight();
prompt();
}
void loop() {
char k = pad.getKey();
if (!k) return;
beep(30);
if (k == '*') { prompt(); return; } // clear
if (k != '#') { if (entry.length() < 8) { entry += k; lcd.print('*'); } return; }
if (entry == code) {
wrong = 0;
lcd.clear(); lcd.print("Open");
digitalWrite(RELAY, ON); delay(5000); digitalWrite(RELAY, !ON); // never hold a solenoid on for long
} else {
wrong++;
lcd.clear(); lcd.print("Wrong code");
beep(wrong >= 3 ? 3000 : 400);
if (wrong >= 3) { lcd.setCursor(0, 1); lcd.print("Wait 30 s"); delay(30000); wrong = 0; }
}
prompt();
}Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Each key press | Short beep and a * on the LCD |
| 1234 then # | "Open", relay clicks, solenoid pulls in for 5 s |
| Wrong code three times | Long beep and a 30 s lockout |
| Solenoid current | About 0.5 to 0.8 A at 12 V while open |
If it does not work
Wrong keys appear
Rows and columns swapped, or the ribbon is reversed. Swap the rows[] and cols[] arrays.
The Uno resets when the lock opens
The flyback diode is missing or reversed. Its stripe must face the solenoid plus.
The solenoid gets hot
It is made for short pulses. Keep the open time to a few seconds.
Safety
A fail-secure solenoid stays locked if power fails. Keep a mechanical key or exit button for real doors.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the keypad password door lock?
Arduino Uno R3, 4x4 matrix keypad (membrane), 16x2 LCD with I2C backpack (PCF8574), Relay Module 5V, Solenoid lock 12 V, Rectifier Diode 1N4007, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), Active buzzer 5 V and Jumper wires male to male (40 pcs, 20 cm). Rectifier Diode 1N4007: Across the solenoid, stripe to plus.
How long does the keypad password door lock take to build?
About 100 minutes for a intermediate maker, in 5 steps.
How do I know the keypad password door lock works?
Each key press: Short beep and a * on the LCD. 1234 then #: "Open", relay clicks, solenoid pulls in for 5 s. Wrong code three times: Long beep and a 30 s lockout.
Wrong keys appear: what should I check?
Rows and columns swapped, or the ribbon is reversed. Swap the rows[] and cols[] arrays.
The Uno resets when the lock opens: what should I check?
The flyback diode is missing or reversed. Its stripe must face the solenoid plus.
The solenoid gets hot: what should I check?
It is made for short pulses. Keep the open time to a few seconds.
Safety: what should I check?
A fail-secure solenoid stays locked if power fails. Keep a mechanical key or exit button for real doors.
