Projects / Engine temperature alarm

Engine temperature alarm

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANOLM2596

    Set the buck module

    Connect 12 V to the LM2596 and turn its trimmer until the output reads 5.0 V on a multimeter.

  2. NANOMAX667524.2°CPCF8574

    Wire the electronics

    Fuse then LM2596, Nano 5V and GND, MAX6675, LCD and buzzer.

  3. NANOMAX667524.3°C

    Test on the bench

    Hold the probe tip in your hand or in hot water. The reading follows.

  4. NANO

    Choose the limit

    Check the engine's maximum normal temperature in its manual and set LIMIT_C below it.

  5. NANOMAX667524.3°C

    Fit the probe

    Clamp or bolt the tip to the cylinder head or block, and run the wire clear of hot and moving parts.

  6. NANO

    Mount the box

    Put it where you can hear the buzzer and keep it out of oil and heat.

In short

How do you build an engine temperature alarm?

A thermocouple on an engine or generator sounds an alarm when it runs too hot. You need Arduino Nano, MAX6675 thermocouple module with K-type probe, 16x2 LCD with I2C backpack (PCF8574), Active buzzer 5 V, LM2596 Buck Module, Fuse 1 A glass (5 × 20 mm), Fuse holder (panel, 5 × 20 mm) and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Vehicle or battery + (12 V)1 A fuse, then LM2596 IN+Fused supply
Vehicle or battery -LM2596 IN- and groundGround
LM2596 OUT+ (set to 5.0 V first)Nano 5V pinRegulated supply
LM2596 OUT-Nano GNDGround
MAX6675 VCC and GNDNano 5V and GNDSupply
MAX6675 SCKNano D6Clock
MAX6675 CSNano D5Chip select
MAX6675 SONano D4Data out
LCD SDA and SCLNano A4 and A5Display
Buzzer + and -Nano D8 and GNDAlarm

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "MAX6675 library" by Adafruit. The K-type probe is rated far above engine temperatures, but its wires must be clipped away from exhaust. Set the LM2596 output to exactly 5.0 V on a multimeter before connecting the Nano, because vehicle supplies spike and sag. This is an indicator and should not replace the engine's own protection.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <max6675.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

MAX6675 thermocouple(6, 5, 4);               // SCK, CS, SO
LiquidCrystal_I2C lcd(0x27, 16, 2);
const byte BUZZ = 8;
const float LIMIT_C = 110.0;                 // set from your engine's manual
float peak = 0;

void setup() {
  pinMode(BUZZ, OUTPUT);
  lcd.init(); lcd.backlight();
  delay(500);                                // let the MAX6675 settle
}

void loop() {
  float t = thermocouple.readCelsius();
  if (!isnan(t)) {
    if (t > peak) peak = t;
    lcd.setCursor(0, 0); lcd.print("Temp "); lcd.print(t, 0); lcd.print(" C   ");
    lcd.setCursor(0, 1); lcd.print("Peak "); lcd.print(peak, 0); lcd.print(" C   ");
    digitalWrite(BUZZ, t > LIMIT_C ? (millis() / 300) % 2 : LOW);
  } else {
    lcd.setCursor(0, 0); lcd.print("Probe error     ");
    digitalWrite(BUZZ, LOW);
  }
  delay(1000);                               // the MAX6675 converts about 4 times a second
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe in hot water at 80 °CReads close to the water temperature
Reading above the limitBuzzer pulses
Peak lineHolds the highest value
Unplug the probeShows Probe error

If it does not work

Reading is always 0 or NaN

The probe is not connected or wired backwards at the module.

Reading jumps around

Electrical noise from the engine. Shield or twist the probe wires and add 100 µF on the 5 V rail.

LCD blank

Check the address 0x27 or 0x3F and contrast trimmer.

Nano resets when the engine cranks

The supply sags. Add a 470 µF capacitor at the buck input.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the engine temperature alarm?

Arduino Nano, MAX6675 thermocouple module with K-type probe, 16x2 LCD with I2C backpack (PCF8574), Active buzzer 5 V, LM2596 Buck Module, Fuse 1 A glass (5 × 20 mm), Fuse holder (panel, 5 × 20 mm) and Jumper wires male to male (40 pcs, 20 cm).

How long does the engine temperature alarm take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the engine temperature alarm works?

Probe in hot water at 80 °C: Reads close to the water temperature. Reading above the limit: Buzzer pulses. Peak line: Holds the highest value.

Reading is always 0 or NaN: what should I check?

The probe is not connected or wired backwards at the module.

Reading jumps around: what should I check?

Electrical noise from the engine. Shield or twist the probe wires and add 100 µF on the 5 V rail.

LCD blank: what should I check?

Check the address 0x27 or 0x3F and contrast trimmer.

Nano resets when the engine cranks: what should I check?

The supply sags. Add a 470 µF capacitor at the buck input.