Projects / Two-player reaction game

Two-player reaction game

Beginner40 minGuided buildReviewed
Arduino UnoD2D3D9D10D11D8GOPlayer 1Player 2P1 winsP2 wins
State: Get ready (0 s)Serial at 9600 baud

Tap a part to see what it does.

Tap the parts to see what each one does. A teaching simulation, not a circuit simulator.

Build it step by step

0 of 4 done
  1. UNO

    Two buttons

    One at each end of the breadboard, D2 and D3 to GND.

  2. UNO16.9 mA

    Three LEDs

    Green D9, red D10, yellow D11, each through 220 Ω.

  3. UNO

    Buzzer

    D8.

  4. UNO

    Play

    Upload, open the serial monitor, and wait for green.

In short

How do you build a two-player reaction game?

After a random wait the green light comes on. The first player to press their button wins; pressing early is a foul. Times show in the serial monitor. You need Arduino Uno R3, Tactile push button 6 mm × 2, LED 5 mm green, LED 5 mm red, LED 5 mm yellow, Resistor 220 Ω × 3, Active buzzer 5 V and Breadboard 830 Tie Points. It takes 4 steps and about 40 minutes.

Level
Beginner
Time
About 40 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Player 1 buttonD2 to GNDINPUT_PULLUP
Player 2 buttonD3 to GNDINPUT_PULLUP
D9 → 220 Ω → green LEDGo light
D10 / D11 → 220 Ω → red / yellow LEDPlayer 1 / Player 2 winner light
BuzzerD8 to GNDStart beep

Code

No libraries. The active buzzer simply beeps; tone() still turns it on and off. Typical reaction times are 200 to 300 ms.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const int P1 = 2, P2 = 3, GO = 9, L1 = 10, L2 = 11, BUZZ = 8;

void setup() {
  for (int p : {GO, L1, L2, BUZZ}) pinMode(p, OUTPUT);
  pinMode(P1, INPUT_PULLUP); pinMode(P2, INPUT_PULLUP);
  Serial.begin(9600);
  randomSeed(analogRead(A0));
}

void loop() {
  digitalWrite(L1, LOW); digitalWrite(L2, LOW);
  Serial.println("Get ready...");
  unsigned long wait = millis() + random(2000, 6000);
  while (millis() < wait) {
    if (!digitalRead(P1)) { Serial.println("Foul by player 1"); digitalWrite(L2, HIGH); delay(2000); return; }
    if (!digitalRead(P2)) { Serial.println("Foul by player 2"); digitalWrite(L1, HIGH); delay(2000); return; }
  }
  digitalWrite(GO, HIGH); tone(BUZZ, 1000, 80);
  unsigned long start = millis();
  while (digitalRead(P1) && digitalRead(P2)) {}
  unsigned long ms = millis() - start;
  bool one = !digitalRead(P1);
  digitalWrite(GO, LOW);
  digitalWrite(one ? L1 : L2, HIGH);
  Serial.print(one ? "Player 1" : "Player 2"); Serial.print(" wins in "); Serial.print(ms); Serial.println(" ms");
  delay(3000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Get ready...

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Wait for green, pressYour light comes on, time prints
Press before greenFoul message, the other player's light comes on
Ten roundsWaits vary between 2 and 6 s

If it does not work

Always player 1

Player 2's button not on D3, or it reads LOW constantly.

Wins with 0 ms

A stuck-down button: check it spans the gap.

Same wait every time

Leave A0 unconnected so randomSeed gets noise.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the two-player reaction game?

Arduino Uno R3, Tactile push button 6 mm × 2, LED 5 mm green, LED 5 mm red, LED 5 mm yellow, Resistor 220 Ω × 3, Active buzzer 5 V and Breadboard 830 Tie Points.

How long does the two-player reaction game take to build?

About 40 minutes for a beginner maker, in 4 steps.

How do I know the two-player reaction game works?

Wait for green, press: Your light comes on, time prints. Press before green: Foul message, the other player's light comes on. Ten rounds: Waits vary between 2 and 6 s.

Always player 1: what should I check?

Player 2's button not on D3, or it reads LOW constantly.

Wins with 0 ms: what should I check?

A stuck-down button: check it spans the gap.

Same wait every time: what should I check?

Leave A0 unconnected so randomSeed gets noise.