Projects / Digital stopwatch

Digital stopwatch

Beginner35 minGuided buildReviewed
Arduino UnoD4D5D2D310:14StopwatchRunningStart/stop

Tap a part to see what it does.

Tap the parts to see what each one does. A teaching simulation, not a circuit simulator.

Build it step by step

0 of 4 done
  1. UNO

    Wire the display

    CLK D4, DIO D5.

  2. UNO

    Two buttons

    Start/stop on D2, reset on D3, both to GND.

  3. UNO

    Upload

    Press start.

  4. UNO

    Check accuracy

    Run it beside a phone stopwatch for a minute.

In short

How do you build a digital stopwatch?

A 4-digit display counts seconds and hundredths. One button starts and stops, the other resets, both debounced in code. You need Arduino Uno R3, TM1637 4-digit display, Tactile push button 6 mm × 2 and Breadboard 830 Tie Points. It takes 4 steps and about 35 minutes.

Level
Beginner
Time
About 35 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
TM1637 CLK / DIOD4 / D5Display
TM1637 VCC / GND5V / GNDPower
Start/stop buttonD2 to GNDINPUT_PULLUP
Reset buttonD3 to GNDINPUT_PULLUP

Code

Library: TM1637Display. The colon separates seconds from hundredths. Extend to minutes by showing MM:SS after 100 s.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>
TM1637Display disp(4, 5);
const int START = 2, RESET = 3;
bool running = false;
unsigned long base = 0, held = 0, lastPress = 0;

bool pressed(int pin) {
  if (digitalRead(pin) == LOW && millis() - lastPress > 250) { lastPress = millis(); return true; }
  return false;
}

void setup() {
  pinMode(START, INPUT_PULLUP); pinMode(RESET, INPUT_PULLUP);
  disp.setBrightness(4);
}

void loop() {
  if (pressed(START)) {
    if (running) held = millis() - base; else base = millis() - held;
    running = !running;
  }
  if (pressed(RESET) && !running) held = 0;
  unsigned long ms = running ? millis() - base : held;
  int shown = (ms / 1000 % 100) * 100 + (ms / 10 % 100);   // SS.hh, rolls over at 100 s
  disp.showNumberDecEx(shown, 0b01000000, true);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Start, wait, stopDisplay freezes on the elapsed time
Start againContinues from the frozen time
One minute against a phoneWithin about 0.1 s

If it does not work

Starts and stops twice per press

Increase the 250 ms debounce.

Reset does nothing

Reset only works while stopped, by design.

Display blank

CLK and DIO swapped.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the digital stopwatch?

Arduino Uno R3, TM1637 4-digit display, Tactile push button 6 mm × 2 and Breadboard 830 Tie Points.

How long does the digital stopwatch take to build?

About 35 minutes for a beginner maker, in 4 steps.

How do I know the digital stopwatch works?

Start, wait, stop: Display freezes on the elapsed time. Start again: Continues from the frozen time. One minute against a phone: Within about 0.1 s.

Starts and stops twice per press: what should I check?

Increase the 250 ms debounce.

Reset does nothing: what should I check?

Reset only works while stopped, by design.

Display blank: what should I check?

CLK and DIO swapped.