Lab / Anna University / Circuits and measurements / Experiment 8

Resonance in series and parallel RLC circuits

Circuits and measurementsVirtual readings4 viva questionsRecord book ready
Open virtual bench
Aim

To find the resonant frequency, bandwidth and Q factor of a series RLC circuit (and observe the parallel case).

Apparatus
  • Function generator
  • Resistor 100 Ω
  • Inductor 10 mH
  • Capacitor 0.1 µF
  • CRO or AC voltmeter
Vout = 2.5 V

Theory

In a series RLC circuit the reactances cancel at f0 = 1 / (2π√(LC)), the impedance is just R and the current is maximum. The bandwidth is the range between the half-power frequencies (current = Imax/√2), BW = R / (2πL), and Q = f0 / BW. A parallel RLC circuit has maximum impedance (minimum current) at resonance.

Read the lesson: Capacitors inductors ›
Circuit connections
  • Generator → R → L → C → ground; measure the voltage across R (proportional to current)

Procedure

Pre-lab check

4 questions · 75% to be ready
1What is the impedance of a series RLC circuit at resonance?
2What is selectivity?
3What happens to the voltage across L and C at resonance?
4Where are resonant circuits used?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
f05.03 kHz
Bandwidth1.59 kHz
Q = f0 / BW3.16
0142741541.5k4.9k8.3k11.7k15.1kf (Hz)I (mA)
f (Hz)|Z| (Ω)I (mA)VR (V)
1510964.45.180.518
2516484.810.311.031
3523251.219.911.991
4278143.734.793.479
4781105.147.564.756
5033100505
5285104.747.784.778
6040153.132.663.266
7549281.917.741.774
10066484.810.311.031
15099849.25.890.589

Precautions

  • Keep the generator output constant at every frequency.
  • Take more readings near resonance.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.f (Hz)|Z| (Ω)I (mA)VR (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

f0 = ___ Hz (theory ___ Hz), bandwidth = ___ Hz, Q = ___.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What is the impedance of a series RLC circuit at resonance?
2. What is selectivity?
3. What happens to the voltage across L and C at resonance?
4. Where are resonant circuits used?

Quick answers for your record and viva

What is the aim of the resonance in series and parallel rlc circuits experiment?

To find the resonant frequency, bandwidth and Q factor of a series RLC circuit (and observe the parallel case).

What apparatus is needed for resonance in series and parallel rlc circuits?

Function generator, Resistor 100 Ω, Inductor 10 mH, Capacitor 0.1 µF, CRO or AC voltmeter.

What is the theory behind resonance in series and parallel rlc circuits?

In a series RLC circuit the reactances cancel at f0 = 1 / (2π√(LC)), the impedance is just R and the current is maximum. The bandwidth is the range between the half-power frequencies (current = Imax/√2), BW = R / (2πL), and Q = f0 / BW. A parallel RLC circuit has maximum impedance (minimum current) at resonance.

What result should I get in resonance in series and parallel rlc circuits?

f0 = ___ Hz (theory ___ Hz), bandwidth = ___ Hz, Q = ___.

What precautions should I take in resonance in series and parallel rlc circuits?

Keep the generator output constant at every frequency. Take more readings near resonance.

Resonance in series and parallel RLC circuits | ElectroLark