Using the multimeter, CRO and function generator
To measure voltage, current, resistance and frequency, and read the amplitude, period and phase of a signal on a CRO.
- Digital multimeter
- CRO (dual channel)
- Function generator
- Resistors 1 kΩ, 10 kΩ
- Capacitor 0.1 µF
- Breadboard and wires
Theory
A multimeter measures DC and AC voltage across a part, current through it (in series) and resistance with the part out of circuit. A CRO plots voltage against time: amplitude is divisions × volts/div, period is divisions × time/div, and frequency is 1/period. With two channels the phase difference is φ = (Δt / T) × 360°, where Δt is the time between matching points on the two waves.
Read the lesson: Measurement ›- Function generator output to CRO CH1, ground clips together
- For phase: generator → 1 kΩ → 0.1 µF → ground; CH1 across the input, CH2 across the capacitor
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| Frequency | Period (ms) | Vc / Vin | Phase lag (°) | Δt (µs) |
|---|---|---|---|---|
| 100 Hz | 10 | 0.998 | 3.6 | 99.9 |
| 500 Hz | 2 | 0.954 | 17.4 | 96.9 |
| 1 kHz | 1 | 0.847 | 32.1 | 89.3 |
| 2 kHz | 0.5 | 0.623 | 51.5 | 71.5 |
| 5 kHz | 0.2 | 0.303 | 72.3 | 40.2 |
Precautions
- Join the ground clips of both probes to the same point.
- Use the CRO's calibration before reading divisions.
- Measure resistance only with the power off.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | Frequency | Period (ms) | Vc / Vin | Phase lag (°) | Δt (µs) |
|---|---|---|---|---|---|
| 1 | |||||
| 2 | |||||
| 3 | |||||
| 4 | |||||
| 5 | |||||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
The frequency and amplitude read on the CRO agree with the generator settings within the reading error, and the measured phase lag matches φ = tan⁻¹(2πfRC).
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva questions
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the using the multimeter, cro and function generator experiment?
To measure voltage, current, resistance and frequency, and read the amplitude, period and phase of a signal on a CRO.
What apparatus is needed for using the multimeter, cro and function generator?
Digital multimeter, CRO (dual channel), Function generator, Resistors 1 kΩ, 10 kΩ, Capacitor 0.1 µF, Breadboard and wires.
What is the theory behind using the multimeter, cro and function generator?
A multimeter measures DC and AC voltage across a part, current through it (in series) and resistance with the part out of circuit. A CRO plots voltage against time: amplitude is divisions × volts/div, period is divisions × time/div, and frequency is 1/period. With two channels the phase difference is φ = (Δt / T) × 360°, where Δt is the time between matching points on the two waves.
What result should I get in using the multimeter, cro and function generator?
The frequency and amplitude read on the CRO agree with the generator settings within the reading error, and the measured phase lag matches φ = tan⁻¹(2πfRC).
What precautions should I take in using the multimeter, cro and function generator?
Join the ground clips of both probes to the same point. Use the CRO's calibration before reading divisions. Measure resistance only with the power off.
