Lab / MAKAUT / Circuits and measurements / Experiment 7

Transient response of RC and RL circuits

Circuits and measurementsVirtual readings4 viva questionsRecord book ready
Open virtual bench
Aim

To observe the charging and discharging of a capacitor through a resistor and measure the time constant τ = RC (and τ = L/R for an RL circuit).

Apparatus
  • Function generator (square wave) or DC supply with a switch
  • Resistor 10 kΩ
  • Capacitor 10 µF (or 0.1 µF with a square wave)
  • CRO or multimeter and stopwatch

Theory

When a step voltage V is applied, the capacitor voltage rises as Vc = V(1 − e^(−t/τ)), with τ = RC. After one τ it reaches 63.2% of V, and after 5τ it is practically full. Discharging follows Vc = V·e^(−t/τ). In an RL circuit the current rises the same way with τ = L/R.

Read the lesson: Capacitors inductors ›
Circuit connections
  • Supply (or square wave) → R → C → ground; CRO across C

Procedure

Pre-lab check

4 questions · 75% to be ready
1What is the time constant?
2After how long is a capacitor considered fully charged?
3What is τ for an RL circuit?
4How does a capacitor behave at the instant of switching and in steady state (DC)?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
τ = RC100 ms
01.352.74.055.40125250375500t (ms)Vc (V)
Vc charging (V)Vc discharging (V)
t (ms)t / τVc charging (V)Vc discharging (V)
0005
500.51.9673.033
10013.1611.839
20024.3230.677
30034.7510.249
40044.9080.092
50054.9660.034

Precautions

  • Connect the electrolytic capacitor with the right polarity.
  • Discharge the capacitor before each new run.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.t (ms)t / τVc charging (V)Vc discharging (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

Measured τ = ___ ms; calculated RC = ___ ms. The capacitor voltage follows the exponential law.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What is the time constant?
2. After how long is a capacitor considered fully charged?
3. What is τ for an RL circuit?
4. How does a capacitor behave at the instant of switching and in steady state (DC)?

Quick answers for your record and viva

What is the aim of the transient response of rc and rl circuits experiment?

To observe the charging and discharging of a capacitor through a resistor and measure the time constant τ = RC (and τ = L/R for an RL circuit).

What apparatus is needed for transient response of rc and rl circuits?

Function generator (square wave) or DC supply with a switch, Resistor 10 kΩ, Capacitor 10 µF (or 0.1 µF with a square wave), CRO or multimeter and stopwatch.

What is the theory behind transient response of rc and rl circuits?

When a step voltage V is applied, the capacitor voltage rises as Vc = V(1 − e^(−t/τ)), with τ = RC. After one τ it reaches 63.2% of V, and after 5τ it is practically full. Discharging follows Vc = V·e^(−t/τ). In an RL circuit the current rises the same way with τ = L/R.

What result should I get in transient response of rc and rl circuits?

Measured τ = ___ ms; calculated RC = ___ ms. The capacitor voltage follows the exponential law.

What precautions should I take in transient response of rc and rl circuits?

Connect the electrolytic capacitor with the right polarity. Discharge the capacitor before each new run.

Transient response of RC and RL circuits: lab experiment