Tools / RC Low-Pass Cutoff

How to work out an RC filter cutoff frequency

Below the cutoff, signals pass. Above it, they get smaller. Here is the working with your numbers.

fc = 1 / (2πRC) for an unloaded first-order RC network

Inputs

Ω
nF

Results update as you type. Prefixes work: 4.7k, 100u, 10n.

Result
Cutoff
1.592 kHz
Time constant
100 µs
What this leaves out
  • Assumes ideal unloaded single-pole RC response; component tolerance and source/load impedance alter cutoff.
Step by step

The working with your numbers

  1. Change the capacitance to faradsC = 10 nF ÷ 1,000,000,000 = 10⁻⁸ F
  2. Multiply R by CR × C = 10,000 × 10⁻⁸ = 100 µs
  3. Divide 1 by 2π × RCfc = 1 ÷ (2π × 0.0001) = 1 ÷ 0.000628 = 1.59 kHz
  4. At the cutoff the output is 70.7 %At 1.59 kHz: Vout = 0.707 × Vin (−3 dB)
  5. Ten times higher it is about 10 %At 15.9 kHz: Vout ≈ 0.1 × Vin (−20 dB)
  6. The phase lag grows with frequencyPhase = −arctan(f ÷ fc): −5.7° at 159 Hz, −45° at 1.59 kHz, −84.3° at 15.9 kHz
  7. The same parts as a high-pass swap the rolesPut C in series and R to ground: the same fc = 1.59 kHz, but low frequencies are cut, with phase +45° at fc.
  8. Worst case with ±5 % R and ±10 % Cfc between 1.38 kHz and 1.86 kHz
See it

How the filter passes each frequency

0 %50 %100 %100 Hz1 kHz10 kHz100 kHzFrequencyfc, 70.7 %
Output against frequency. Flat below 1.59 kHz, then falling 20 dB for every ten times higher frequency.

Does the answer make sense?

  • OK: Check: a bigger R or C gives a lower cutoff. Double C and fc halves to 796 Hz.
  • OK: To smooth PWM, put the cutoff at least 100 times below the PWM frequency. For 490 Hz Arduino PWM that means fc under about 5 Hz.

Pick a real part

  • Nearest standard values: R = 10 kΩ, C = 10 nF, giving fc = 1.59 kHz.
  • The next stage's input should be at least 10 × R (100 kΩ), or the cutoff moves.

Common mistakes

  • Leaving out the 2π. 1 ÷ RC gives a number 6.28 times too high.
  • Thinking frequencies above the cutoff disappear. They only shrink, by about 10 times for every 10 times higher in frequency.
  • Forgetting the load. A low-resistance load on the capacitor changes the cutoff.

Learn it, try it, build it

Calculated, not measured. Check the exact part datasheet and your real circuit before powering anything.

Just need the number? Use the RC low-Pass cutoff calculator on Geekobot.

Common questions

How do you work out the cutoff frequency of an RC filter?

fc = 1 ÷ (2π × R × C), with R in ohms and C in farads. 10 kΩ and 10 nF give 1 ÷ (6.283 × 0.0001) ≈ 1.59 kHz.

What does −3 dB at the cutoff frequency mean?

At the cutoff the output voltage is 70.7 % of the input, which is half the power. Above it, the output keeps falling by about 10 times for every 10 times higher in frequency.