Personal safety band with SOS location
Many women travel alone on late buses and cabs. A small band whose hidden button sends the live location to chosen contacts, and sounds a loud alarm, is a common and valued final-year topic.
- Parts
- ₹3,290
- Build
- 13 weeks
- Board
- ESP32
- Objectives
- 6
Block diagram
- SOS buttonStarts the alert
- GPS moduleGives the location
- ESP32Runs the alert sequence
- Battery packKeeps it wearable
- Power monitorMeasures current to work out battery life+
- 4G modemSends SMS and calls
- BuzzerDraws attention
- Phone appShows readings and sends commands over Bluetooth+
Objectives
- To send an SMS with a map link within 30 seconds of the SOS press (long press, so it is not set off by accident).
- To call the first contact automatically.
- To send updated locations every two minutes until cancelled.
- To measure battery life in standby and during an alert.
- To monitor and control the system from a phone over Bluetooth.
- To reduce average current with sleep modes and verify the battery life by measurement.
Parts and specifications
- ESP32 DevKit V1Dual-core 240 MHz, 520 KB SRAM, Wi-Fi + Bluetooth, 3.3 V logic, 12-bit ADC (use ADC1 pins when Wi-Fi is on)₹450Buy
- NEO-6M GPS module2.5 m CEP accuracy, 1 Hz NMEA on UART 9600, cold start about 27 s, needs open sky₹450Buy
- A7670C 4G LTE module4G Cat-1 with 2G fallback, SMS, calls and data, works with any Indian SIM including Jio; 3.4 to 4.2 V, 2 A peaks₹1,500Buy
- TP4056 charger with protection1 A CC/CV Li-ion charging to 4.2 V, DW01 protection cuts at about 2.5 V₹40Buy
- Band, wires and 3D-printed case₹250
Total about ₹3,290 at typical online prices. Tap a part for its pinout and datasheet notes.
Design calculations
Require 2 s hold so knocks do not trigger. At 100 Hz sampling that is 200 consecutive low reads.
An SMS every 2 minutes for 30 minutes = 15 SMS per alert, within any SMS pack.
Modem in sleep 2 mA, GPS backup off, ESP32 deep sleep 0.15 mA ≈ 2.5 mA total. 2600 mAh × 0.8 / 2.5 mA ≈ 35 days. During an alert about 250 mA average gives about 8 hours.
Pin map
| Signal | Pin or connection |
|---|---|
| SOS button | GPIO 27 (pull-up, long press 2 s) |
| GPS TX → RX1 | GPIO 4 |
| A7670C TX/RX / PWRKEY | GPIO 16 / 17 / GPIO 5 |
| Buzzer (via transistor) | GPIO 26 |
| Battery sense | GPIO 34 via divider |
Firmware outline
- Deep sleep with the SOS pin as wake source.
- On wake, confirm a 2 s press, then power up GPS and the modem.
- Sound the buzzer pattern and send an SMS with the map link (or 'location pending').
- Call the first contact with ATD.
- Every 2 minutes send the updated location until the button is held 5 s to cancel.
- Return to deep sleep after cancel.
Test plan
| Test | Expected result |
|---|---|
| Short tap | No alert |
| 2 s press | SMS within 30 s with a working map link |
| Alert running | Updates every 2 minutes |
| Cancel hold | Stops and sends 'I am safe' |
| Standby over 3 days | Current measured, life worked out |
These rows start your results table when you plan the project.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 5.
Make it yours
One or two upgrades for a mini project, two to four for a major one.
Build these first
Datasheets and sources to cite
- u-blox NEO-6 datasheet
- SIMCom A7670 series AT command manual
- NCRB Crime in India report
About this project
How much does the personal safety band with sos location project cost?
About ₹3,110 for the parts in the base list: ESP32 DevKit V1, NEO-6M GPS module, A7670C 4G LTE module, 12 V piezo alarm, Push button 12 mm, 18650 cell 2600 mAh (branded), TP4056 charger with protection, MT3608 boost (3.7 V to 5 V), Band, wires and 3D-printed case.
How long does it take?
About 10 weeks for the base project, built on an ESP32. Each upgrade adds time.
Which branches is it suitable for?
Electronics and Communication, Computer Science / IT (IoT, AI), Instrumentation, as a major project.
Which pins and design calculations does it use?
SOS button on GPIO 27 (pull-up, long press 2 s); GPS TX → RX1 on GPIO 4; A7670C TX/RX / PWRKEY on GPIO 16 / 17 / GPIO 5. Worked calculations on this page: long press, data cost, standby life.
How do I test it?
Short tap: No alert. 2 s press: SMS within 30 s with a working map link. Alert running: Updates every 2 minutes. Cancel hold: Stops and sends 'I am safe'. Standby over 3 days: Current measured, life worked out.
What are the objectives?
To send an SMS with a map link within 30 seconds of the SOS press (long press, so it is not set off by accident). To call the first contact automatically. To send updated locations every two minutes until cancelled. To measure battery life in standby and during an alert.
