Build it step by step
0 of 8 doneBuild the regulator
9 V, 330 ohm, Zener to GND, banded end at the output.
Check the polarity
Banded end toward the positive side.
Measure with no load
Meter on the output node.
Add 4.7 kilohm
Note the output.
Add 1 kilohm
Note the output.
Add 330 ohm
The output falls below 5.1 V.
Add 220 ohm
It falls further.
Plot
Output against load current for your five readings.
How do you build a zener regulation test?
A Zener and a resistor hold a voltage steady while the load changes, and you measure where it stops working. You need Zener diode 5.1 V (1N4733A), Resistor 330 Ω, Resistor 220 Ω, Resistor 1 kΩ, Resistor 4.7 kΩ, 9 V battery, 9 V battery snap with DC jack, Digital multimeter and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 9
Parts list
- SemiconductorsBuy
- PassivesBuyResistor 330 Ω × 1
- PassivesBuyResistor 220 Ω × 1
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 4.7 kΩ × 1
- BatteriesBuy9 V battery × 1
- PowerBuy
- Tools & InstrumentsBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery positive (red) | 330 ohm resistor | Series resistor |
| 330 ohm resistor | Zener cathode (banded end) and output node | Regulated output |
| Zener anode | 9 V battery negative (black) | Common ground |
| Load resistor (changed each test) | Output node to GND | The load |
| Multimeter red probe | Output node | Reads the regulated voltage |
| Multimeter black probe | Battery negative | Common ground |
Code
A Zener diode is a diode that is used in reverse. Once the reverse voltage reaches its rated value, here 5.1 volts, it conducts and holds the voltage almost constant over a wide range of current. With a series resistor from a 9 volt battery, it makes a simple 5.1 volt reference. The resistor sets the current: 9 minus 5.1 volts across 330 ohms gives about 12 milliamps. The load takes some of that current and the Zener carries the rest, so while the load stays under about 12 milliamps the output hardly moves. That is load regulation, and you can see it by measuring the output with no load, then with 4.7 kilohms and with 1 kilohm. Then the lesson on limits: a 330 ohm load needs more current than the resistor can supply, the Zener switches off, and the output drops to about 4.5 volts. A 220 ohm load drops it to about 3.6 volts. Power matters too. The Zener dissipates its voltage times its current, here only about 60 milliwatts, so it stays cold, but a larger current or a higher input voltage would heat it. This circuit is fine for references and small signals. It is not efficient for powering anything bigger, which is where linear or switching regulators take over. Use fresh connections and never leave the battery connected to the circuit with a short across the output.
Build notes (no code needed for this build) Circuit: 9 V -> 330 ohm -> output node -> 5.1 V Zener to GND (banded end at the output node). Series current with no load: (9 - 5.1) / 330 = about 11.8 mA, so the Zener dissipates about 60 mW. That is far below the 1 W rating of a 1N4733A, so nothing gets hot. Expected output for each load, calculated: No load : about 5.1 V (Zener carries all 11.8 mA) 4.7 kilohm load : about 5.1 V (load takes about 1.1 mA) 1 kilohm load : about 5.1 V (load takes about 5.1 mA, Zener still has about 6.7 mA) 330 ohm load : about 4.5 V (load needs more than the resistor can give, the Zener turns off) 220 ohm load : about 3.6 V (the divider of 330 and 220 ohm, no regulation) The Zener works only while it keeps some current. When the load asks for all of the series current, the output follows the divider and falls. Real values move with the Zener tolerance (about 5 percent) and the battery voltage (a used battery may be 8 V). Optional line regulation test: swap the 9 V battery for a 6 V pack of four AA cells and note how little the output changes while the Zener has current.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| No load | About 5.1 V |
| 4.7 kilohm load | About 5.1 V |
| 1 kilohm load | About 5.1 V, within a few tens of millivolts |
| 330 ohm load | About 4.5 V |
| 220 ohm load | About 3.6 V |
If it does not work
Output about 0.7 V
The Zener is the wrong way round, swap it.
Output equals the battery voltage
The Zener is not connected to ground.
Output never reaches 5 V
Check for a load left connected or a weak battery.
Resistor or Zener warm
Check the resistor value is 330 ohm and the load is not a short.
Readings vary
Check the breadboard contacts.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the zener regulation test?
Zener diode 5.1 V (1N4733A), Resistor 330 Ω, Resistor 220 Ω, Resistor 1 kΩ, Resistor 4.7 kΩ, 9 V battery, 9 V battery snap with DC jack, Digital multimeter and Breadboard 830 Tie Points.
How long does the zener regulation test take to build?
About 60 minutes for a beginner maker, in 8 steps.
How do I know the zener regulation test works?
No load: About 5.1 V. 4.7 kilohm load: About 5.1 V. 1 kilohm load: About 5.1 V, within a few tens of millivolts.
Output about 0.7 V: what should I check?
The Zener is the wrong way round, swap it.
Output equals the battery voltage: what should I check?
The Zener is not connected to ground.
Output never reaches 5 V: what should I check?
Check for a load left connected or a weak battery.
Resistor or Zener warm: what should I check?
Check the resistor value is 330 ohm and the load is not a short.
