Projects / Transistor current mirror lab

Transistor current mirror lab

Intermediate1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Build the reference side

    Resistor, Q1 with base joined to collector.

  2. Calculate

    Work out the reference current.

  3. BC5472N3906

    Add the mirror transistor

    Join the bases and put the load on Q2.

  4. Measure the load voltage

    Calculate the current as voltage divided by the load.

  5. Change the load

    Try 1 kΩ, 2 kΩ (two in series) and 10 kΩ.

  6. Find the limit

    Use a larger load until the current falls.

  7. 2N3906

    Build the PNP mirror

    Repeat with the 2N3906 pair.

In short

How do you build a transistor current mirror lab?

Two matched transistors copy a current from one branch to another, a building block inside every IC. You need BC547 NPN transistor × 2, 2N3906 PNP transistor × 2, Resistor 10 kΩ × 2, Resistor 1 kΩ × 2, Digital multimeter, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 60 minutes.

Level
Intermediate
Time
About 60 min
Parts
8
See the electronics first. This build uses transistor switch. Try a transistor switch in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery ++ railSupply
9 V battery -- railGround
10 kΩ resistor (reference)+ rail and BC547 Q1 collectorSets the reference current
Q1 collectorQ1 base and Q2 baseDiode-connected, the mirror input
Q1 emitter and Q2 emitter- railGround
Q2 collectorLoad resistor then + railMirror output, load of 1 kΩ to start
MultimeterAcross the load resistorRead the load voltage, then calculate the current

No code needed

No code. The reference resistor sets a current of about (9 − 0.65) ÷ 10 kΩ = 0.84 mA through Q1, whose base and collector are joined. Q2 has the same base-emitter voltage, so it passes nearly the same current whatever the load, as long as its collector voltage stays above about 0.2 V. With a 1 kΩ load the load voltage should read about 0.84 V; with 2 kΩ about 1.7 V, and with 10 kΩ about 8.3 V, though a 10 kΩ load leaves Q2 almost at its limit. Real transistors differ a little, so expect the copy to be within about 5 to 10 percent, and best if you use two from the same batch. Try the PNP mirror last: put two 2N3906 with emitters on the + rail, the reference resistor from the joined base and collector to ground, and the load on the other collector to ground. Check the 2N3906 pinout in its datasheet.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
1 kΩ loadAbout 0.8 V across it
2 kΩ loadAbout 1.7 V across it, same current
Very large loadCurrent falls once Q2 can no longer stay in its active region
PNP mirrorSame behaviour mirrored

If it does not work

Output current is far from the reference

The transistors are very different or one is warm; use a matched pair.

No current

Check the base joins and emitter grounds.

Load voltage too large

The load is too big and Q2 is saturated.

Readings drift

Do not touch the transistors, since warming them changes the current.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the transistor current mirror lab?

BC547 NPN transistor × 2, 2N3906 PNP transistor × 2, Resistor 10 kΩ × 2, Resistor 1 kΩ × 2, Digital multimeter, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. BC547 NPN transistor × 2: Matched pair.

How long does the transistor current mirror lab take to build?

About 60 minutes for a intermediate maker, in 7 steps.

How do I know the transistor current mirror lab works?

1 kΩ load: About 0.8 V across it. 2 kΩ load: About 1.7 V across it, same current. Very large load: Current falls once Q2 can no longer stay in its active region.

Output current is far from the reference: what should I check?

The transistors are very different or one is warm; use a matched pair.

No current: what should I check?

Check the base joins and emitter grounds.

Load voltage too large: what should I check?

The load is too big and Q2 is saturated.

Readings drift: what should I check?

Do not touch the transistors, since warming them changes the current.