Build it step by step
0 of 8 donePlan the layout
Sketch the order of blocks on paper.
Mount the strip and blocks
Fix them to the board.
Make the buses
Red jumpers on 1 to 4, black on 5 to 8.
Wire the two-pin blocks
One wire to each bus.
Wire the three-pin blocks
Positive, ground, signal in a fixed order.
Label every terminal
Tape and pen.
Test continuity
Positive to positive beeps, positive to ground does not.
Test with a supply
Check the voltage at several terminals.
How do you build a terminal block hub board?
Mount screw terminal blocks and a barrier strip on a board to make a neat low-voltage power and signal hub for bench projects. You need Screw terminal block 2-pin (5 mm) × 4, Screw terminal block 3-pin (5 mm) × 2, Terminal block 12-way (barrier strip), Silicone wire 22 AWG (assorted colours), Screwdriver set (precision) and Digital multimeter. It takes 8 steps and about 120 minutes.
- Level
- Beginner
- Time
- About 120 min
- Parts
- 6
Wiring
| From | To | Why |
|---|---|---|
| Barrier strip terminals 1 to 4 | Joined with short red jumpers | Positive bus, four connection points |
| Barrier strip terminals 5 to 8 | Joined with short black jumpers | Ground bus, four connection points |
| Barrier strip terminals 9 to 12 | Left separate and labelled | Spare signal terminals |
| Four 2-pin blocks | One wire to the positive bus, one to the ground bus | Supply in and supply out points |
| Two 3-pin blocks | Positive, ground and signal | Sensor connectors with the same order every time |
| Every wire end | Stripped 6 mm, fully under the screw clamp | Tight and no loose strands outside |
Code
A hub board brings order to a bench full of loose wires. A barrier strip has twelve separate terminals, and by joining groups of four with short jumpers you make a positive bus and a ground bus with four connection points each, plus four spare terminals for signals. Screw terminal blocks add supply connections and sensor connectors with a fixed pin order, positive, ground and signal, so you never have to wonder which way round a sensor goes. Wire ends should be stripped about 6 millimetres so the bare copper sits fully under the clamp, with no loose strands sticking out where they could touch the next terminal, and each screw must be tight enough that a tug on the wire does not move it. Label every terminal with tape before you connect anything. The most important step is the continuity test: with the meter on its beeper, every positive terminal should beep to every other positive terminal and never to a ground terminal, and the same for ground. Only then connect a low-voltage supply, with the correct polarity, and measure the voltage at a few terminals. Keep it for low-voltage work only, and never use it with mains.
Build notes (no code needed for this build)
Purpose: a tidy hub for low-voltage bench projects. Maximum 24 V DC and a few amps. This is NOT for mains. Keep mains voltage away from this board.
Layout plan
Barrier strip 12 terminals, left to right:
1 to 4 joined together with red jumpers, the positive bus (+V)
5 to 8 joined together with black jumpers, the ground bus (GND)
9 to 12 spare signal terminals, left separate
Two-pin blocks (four): supply in, supply out and two spares. Each connects to the +V bus and the GND bus.
Three-pin blocks (two): order is +V, GND, SIGNAL in the same direction every time, so sensors plug in the same way.
Colour code: red for positive, black for ground, yellow or another colour for signal. Use 22 AWG silicone wire.
Method
1. Lay the blocks on the board and plan the order before drilling or fixing anything.
2. Fix the barrier strip and blocks to a scrap board with screws or double-sided mounting tape.
3. Cut short jumpers of about 3 cm and strip 6 mm from each end.
4. Join terminals 1 to 4 with red and 5 to 8 with black. Tighten every screw firmly and tug each wire.
5. Wire each two-pin block to the buses.
6. Wire the three-pin blocks: +V, GND and signal.
7. Label every terminal with tape: +V, GND, S1 to S4 and so on.
8. Test with the multimeter on continuity: every +V terminal should beep with every other +V terminal and NOT with any GND terminal. Repeat for GND.
9. Connect a low-voltage supply last, with the correct polarity, and check the voltage at several terminals.
Safety: put an inline fuse of about 2 A on the supply lead if you have one. Never connect reverse polarity to boards that do not have protection, and never bridge +V to GND. Check with the meter before connecting a board.Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Positive to positive terminals | Beep, under 1 ohm |
| Positive to ground terminals | No beep |
| Spare terminals | Not connected to any bus |
| Supply of 5 V connected | 5 V at every positive terminal |
| Tug on each wire | No wire moves |
If it does not work
A terminal does not beep
Re-tighten the screw and check the wire is under the clamp.
Positive beeps to ground
A loose strand is touching, strip and remake that joint.
Voltage is low
Check the supply and the wire gauge.
Wire pulls out
Strip a little longer and tighten harder.
Sensors plug in wrongly
Keep the three-pin order the same on every block.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the terminal block hub board?
Screw terminal block 2-pin (5 mm) × 4, Screw terminal block 3-pin (5 mm) × 2, Terminal block 12-way (barrier strip), Silicone wire 22 AWG (assorted colours), Screwdriver set (precision) and Digital multimeter.
How long does the terminal block hub board take to build?
About 120 minutes for a beginner maker, in 8 steps.
How do I know the terminal block hub board works?
Positive to positive terminals: Beep, under 1 ohm. Positive to ground terminals: No beep. Spare terminals: Not connected to any bus.
A terminal does not beep: what should I check?
Re-tighten the screw and check the wire is under the clamp.
Positive beeps to ground: what should I check?
A loose strand is touching, strip and remake that joint.
Voltage is low: what should I check?
Check the supply and the wire gauge.
Wire pulls out: what should I check?
Strip a little longer and tighten harder.
