Voltage and resistor reference board
Build it step by step
0 of 7 doneBuild the reference
1 kΩ, TL431 and the pads.
Measure 2.5 V
With the best meter.
Add the 5 V divider
Two 10 kΩ resistors.
Test your meters
Record each reading.
Test the resistors
1 kΩ and 10 kΩ.
Write the errors
A card for each meter.
Repeat later
Every few months.
How do you build a voltage and resistor reference board?
A TL431 reference and precision resistors give known values to check your meters. You need TL431 adjustable shunt reference, Resistor 1 kΩ × 2, Resistor 10 kΩ × 2, Digital multimeter, Perfboard (dot PCB) 7 × 9 cm, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 45 minutes.
- Level
- Intermediate
- Time
- About 45 min
- Parts
- 7
Parts list
- Integrated CircuitsBuy
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuyResistor 10 kΩ × 2
- Tools & InstrumentsBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery plus | 1 kΩ resistor to the TL431 cathode | Bias current |
| TL431 anode | Battery minus | Ground |
| TL431 reference pin | Cathode | 2.5 V output |
| Optional: 10 kΩ from cathode to reference, 10 kΩ from reference to ground | Second output about 5 V | Two reference voltages |
| Output pads | Cathode node and ground | Test points |
| Resistor test pads | 1 kΩ and 10 kΩ resistors to pads | Reference resistances |
No code needed
This lab has no code. The TL431 is a shunt reference: with its reference pin tied to the cathode it holds about 2.495 V, and with a 10 kΩ and 10 kΩ divider from cathode to reference to ground it holds about 5 V. A 1 kΩ resistor from the 9 V battery feeds it a few milliamps, comfortably above its 1 mA minimum. Measure the output with every meter you own and note the readings; the TL431A is good to about plus or minus 1 percent, so it tells you whether a meter is roughly right, but it is not a calibrator for exact work. Do the same with the 1 kΩ and 10 kΩ resistors on the pads, which are 1 percent metal film. Write each meter's error on a card taped inside its case, and repeat every few months, especially after a battery change. Do not put a capacitor on the output, as TL431 devices can oscillate with certain capacitive loads, and do not connect the board to anything powered from mains.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Reference | 2.49 to 2.51 V |
| Divided output | About 5.0 V |
| Meters | Agree within their stated accuracy |
| Resistors | Within 1 percent of the marked value |
If it does not work
Output wrong
Check the reference pin connection.
Output unstable
Remove any capacitor from the output.
Meters disagree
Check battery and leads, then re-measure.
Reference drifts
Allow time to warm up and use a fresh battery.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the voltage and resistor reference board?
TL431 adjustable shunt reference, Resistor 1 kΩ × 2, Resistor 10 kΩ × 2, Digital multimeter, Perfboard (dot PCB) 7 × 9 cm, 9 V battery and 9 V battery snap with DC jack.
How long does the voltage and resistor reference board take to build?
About 45 minutes for a intermediate maker, in 7 steps.
How do I know the voltage and resistor reference board works?
Reference: 2.49 to 2.51 V. Divided output: About 5.0 V. Meters: Agree within their stated accuracy.
Output wrong: what should I check?
Check the reference pin connection.
Output unstable: what should I check?
Remove any capacitor from the output.
Meters disagree: what should I check?
Check battery and leads, then re-measure.
Reference drifts: what should I check?
Allow time to warm up and use a fresh battery.
