Projects / 360° photo turntable

360° photo turntable

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Test the stepper alone

    Turn it one full revolution.

  2. NANO

    Mount a flat plate

    Centred on the shaft.

  3. NANO

    Add the HC-05

    Use the divider on RXD.

  4. NANOHC05

    Pair the phone

    Open a Bluetooth terminal.

  5. NANO

    Upload the sketch

    Press the button.

  6. NANO

    Set the phone camera timer

    About 4 seconds apart.

  7. NANO

    Check the 24 photos

    Make a turning image.

In short

How do you build a 360° photo turntable?

A stepper turns a product turntable in 24 steps with a pause at each position, for 360° product photos taken by a phone on a timer. You need Arduino Nano, 28BYJ-48 Stepper Motor, ULN2003 driver board, HC-05 Bluetooth Module, Tactile push button 6 mm, 5 V 2 A USB adapter and Resistor 1 kΩ × 3. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
ULN2003 IN1, IN2, IN3, IN4Nano D8, D9, D10, D11Stepper coils
ULN2003 plus and minus5V adapterMotor power (join its ground to the Nano GND)
Stepper plugULN2003 socket28BYJ-48 motor
HC-05 TXDNano D2Commands from the phone
HC-05 RXDNano D3 through a divider (1 k to RXD, 1 k plus 1 k to GND)Brings 5 V down to about 3.3 V
HC-05 VCC and GNDNano 5V and GNDPower
Start buttonNano D4 and GNDStarts a turn (internal pull-up)

Code

A 28BYJ-48 stepper makes 2048 full steps per turn, so 24 equal positions are about 85.3 steps apart. The sketch works out each target position from the total and moves the difference, so the rounding never builds up and the plate is back at the start after 24 shots. After each move it releases the coils so the motor stays cool, waits for the model to settle, then sends a SHOT message over the HC-05 and waits again. Be clear about what the HC-05 can and cannot do: it is a Bluetooth serial module, not a Bluetooth remote shutter, so it cannot press the camera button for you. Use your phone's camera timer or an interval-shooting app set to take a picture about every four seconds, matched to the pause in the sketch, and use the SHOT messages in a terminal app to see where the turn is. Start a turn with the button or by sending the letter G from the same terminal. Use a slow speed and a light, centred object, and keep fingers away from the plate. The HC-05 takes 3.3 V on its RXD pin, hence the divider. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// 360 degree photo turntable: 24 positions per turn, pause at each, report over Bluetooth.
// Library: Stepper (built in), SoftwareSerial. Board: Arduino Nano. 28BYJ-48: 2048 full steps per turn.
#include <Stepper.h>
#include <SoftwareSerial.h>
const int STEPS_PER_REV = 2048;
const int SHOTS = 24;
const unsigned long SETTLE_MS = 1500;     // wait for the model to stop wobbling
Stepper st(STEPS_PER_REV, 8, 10, 9, 11);  // coil order for the 28BYJ-48
SoftwareSerial bt(2, 3);                   // RX, TX
const uint8_t BTN = 4;
long position = 0;
void releaseCoils() {
  for (uint8_t p = 8; p <= 11; p++) digitalWrite(p, LOW);   // stops the motor getting warm
}
void runTurn() {
  position = 0;
  for (int i = 1; i <= SHOTS; i++) {
    long target = (long)i * STEPS_PER_REV / SHOTS;
    st.step(target - position);
    position = target;
    releaseCoils();
    delay(SETTLE_MS);
    bt.print("SHOT "); bt.println(i);
    Serial.print("SHOT "); Serial.println(i);
    delay(2500);                            // time for the phone's interval timer to take a photo
  }
  bt.println("DONE");
}
void setup() {
  Serial.begin(9600);
  bt.begin(9600);
  pinMode(BTN, INPUT_PULLUP);
  st.setSpeed(10);                           // rpm, slow and smooth
  releaseCoils();
}
void loop() {
  if (digitalRead(BTN) == LOW) { delay(30); while (digitalRead(BTN) == LOW) {} runTurn(); }
  if (bt.available() && bt.read() == 'G') runTurn();   // send the letter G from a Bluetooth terminal app
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press the buttonPlate moves in 24 equal steps
After the 24thPlate is back where it started
Phone terminalShows SHOT 1 to SHOT 24
Motor after the turnWarm at most, not hot

If it does not work

Motor only buzzes

The coil order is wrong; use 8, 10, 9, 11.

Plate drifts

Check the 2048 step count and no slipping on the shaft.

No Bluetooth text

Check the divider and swap TX and RX.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the 360° photo turntable?

Arduino Nano, 28BYJ-48 Stepper Motor, ULN2003 driver board, HC-05 Bluetooth Module, Tactile push button 6 mm, 5 V 2 A USB adapter and Resistor 1 kΩ × 3.

How long does the 360° photo turntable take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the 360° photo turntable works?

Press the button: Plate moves in 24 equal steps. After the 24th: Plate is back where it started. Phone terminal: Shows SHOT 1 to SHOT 24.

Motor only buzzes: what should I check?

The coil order is wrong; use 8, 10, 9, 11.

Plate drifts: what should I check?

Check the 2048 step count and no slipping on the shaft.

No Bluetooth text: what should I check?

Check the divider and swap TX and RX.