Projects / Macro focus stacking rail

Macro focus stacking rail

Intermediate4 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOLEAD

    Build the rail

    Mount the lead screw and the camera carriage.

  2. NANO

    Test the motor

    Move one turn and measure 8 mm.

  3. NANO

    Wire the driver

    Add the capacitor first.

  4. NANO

    Test the step sizes

    Move 50 micrometres, check with a dial gauge if you have one.

  5. NANOPC817

    Wire the shutter

    Optocoupler to the camera's release cable.

  6. NANO

    Run a short stack

    Ten shots of a small object.

  7. NANO

    Merge

    Combine the photos in stacking software.

In short

How do you build a macro focus stacking rail?

A stepper moves a camera a tiny distance between shots to build sharp macro images. You need Arduino Nano, Stepper motor 35 mm (NEMA 14), TMC2208 stepper driver, Lead screw T8 with nut (300 mm), Tactile push button 6 mm × 2, 16x2 LCD with I2C backpack (PCF8574), 12 V 2 A DC adapter, Optocoupler PC817, Resistor 1 kΩ and Electrolytic Capacitor 100 µF. It takes 7 steps and about 240 minutes.

Level
Intermediate
Time
About 240 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
TMC2208 VM and GND12 V adapter plus and minusMotor supply
100 µF capacitorAcross VM and GND at the driverAbsorbs spikes
TMC2208 VIO and GNDNano 5V and GNDLogic supply
TMC2208 STEPNano D3Step pulses
TMC2208 DIRNano D4Direction
TMC2208 ENNano D8Enable (LOW = on)
TMC2208 MS1 and MS2GND1/8 microsteps in standalone mode
TMC2208 coil outputsNEMA 14 motorCheck the coil pairs with a multimeter
Start buttonNano D2 and GNDStart and stop
Step size buttonNano D5 and GNDCycle the step size
Nano D61 kΩ to PC817 LED anode, cathode to GNDShutter signal
PC817 transistor sideCamera's remote release cable (shutter and ground)Isolated shutter trigger (check the camera's pinout)
LCD SDA and SCLNano A4 and A5Status

Code

Focus stacking takes many photos with the focus point moved a tiny distance each time, then merges the sharp parts in free software such as Helicon Focus, Zerene or the open-source Enfuse. A rail moves the whole camera forward in very small steps. A T8 lead screw moves 8 mm per turn; with the driver's standard 1/8 microstepping, one microstep is 5 micrometres, so a 25 micrometre step is 5 microsteps. Pick a step size from the table by the depth of field of your lens, usually smaller for higher magnification. The camera is triggered through an optocoupler, which keeps the Arduino electrically isolated from the camera; connect the PC817's output to the camera's remote release cable as its manual describes, and never put 5 V on a camera's own socket. Remote release pinouts differ by make and model, so check yours. Keep the camera on a firm rail, shield the lens from vibration, and never connect or disconnect the motor while the supply is on. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Focus stacking rail. Libraries: LiquidCrystal_I2C. Board: Arduino Nano. No stepper library needed.
// T8 lead screw: 8 mm per turn. 200 full steps x 8 microsteps = 1600 steps per turn, so one microstep = 5 micrometres.
#include <Wire.h>
#include <LiquidCrystal_I2C.h>

LiquidCrystal_I2C lcd(0x27, 16, 2);
const int STEP = 3, DIR = 4, EN = 8, BTN_GO = 2, BTN_SZ = 5, SHUTTER = 6;
const int SIZES_UM[5] = {10, 25, 50, 100, 250};          // step size choices in micrometres
const int SHOTS = 40;
int sizeIdx = 1; bool running = false; int shot = 0; unsigned long lastBtn = 0;

void stepMotor(long steps, bool forward) {
  digitalWrite(DIR, forward ? HIGH : LOW);
  for (long i = 0; i < steps; i++) { digitalWrite(STEP, HIGH); delayMicroseconds(400); digitalWrite(STEP, LOW); delayMicroseconds(400); }
}

void showStatus() {
  lcd.clear(); lcd.print("Step "); lcd.print(SIZES_UM[sizeIdx]); lcd.print(" um");
  lcd.setCursor(0, 1); lcd.print(running ? "Shot " : "Ready "); if (running) { lcd.print(shot); lcd.print("/"); lcd.print(SHOTS); }
}

void setup() {
  pinMode(STEP, OUTPUT); pinMode(DIR, OUTPUT); pinMode(EN, OUTPUT); pinMode(SHUTTER, OUTPUT);
  pinMode(BTN_GO, INPUT_PULLUP); pinMode(BTN_SZ, INPUT_PULLUP);
  digitalWrite(EN, LOW);
  lcd.init(); lcd.backlight(); showStatus();
}

void loop() {
  if (!digitalRead(BTN_SZ) && !running && millis() - lastBtn > 300) { sizeIdx = (sizeIdx + 1) % 5; lastBtn = millis(); showStatus(); }
  if (!digitalRead(BTN_GO) && millis() - lastBtn > 400) { running = !running; shot = 0; lastBtn = millis(); showStatus(); }
  if (running && shot < SHOTS) {
    delay(1500);                                          // let the vibration settle before the exposure
    digitalWrite(SHUTTER, HIGH); delay(200); digitalWrite(SHUTTER, LOW);
    delay(1500);                                          // exposure and saving time
    stepMotor(SIZES_UM[sizeIdx] / 5, true);               // move the camera forward one step
    shot++; showStatus();
    if (shot >= SHOTS) { running = false; stepMotor(SIZES_UM[sizeIdx] / 5 * SHOTS, false); showStatus(); }   // return to the start
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
One turnCarriage moves 8 mm
Press startShutter fires, camera moves, repeat
40 shots doneCamera returns to the start
MergeSharp image from front to back

If it does not work

Shutter does not fire

Check the optocoupler side and the camera's pinout.

Steps are uneven

Remove backlash by always approaching from one direction.

Motor buzzes

Check the coil pairs and the supply.

Photos blur

Wait longer for vibration to settle.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the macro focus stacking rail?

Arduino Nano, Stepper motor 35 mm (NEMA 14), TMC2208 stepper driver, Lead screw T8 with nut (300 mm), Tactile push button 6 mm × 2, 16x2 LCD with I2C backpack (PCF8574), 12 V 2 A DC adapter, Optocoupler PC817, Resistor 1 kΩ and Electrolytic Capacitor 100 µF.

How long does the macro focus stacking rail take to build?

About 240 minutes for a intermediate maker, in 7 steps.

How do I know the macro focus stacking rail works?

One turn: Carriage moves 8 mm. Press start: Shutter fires, camera moves, repeat. 40 shots done: Camera returns to the start.

Shutter does not fire: what should I check?

Check the optocoupler side and the camera's pinout.

Steps are uneven: what should I check?

Remove backlash by always approaching from one direction.

Motor buzzes: what should I check?

Check the coil pairs and the supply.

Photos blur: what should I check?

Wait longer for vibration to settle.