Projects / Stepper motor that follows a knob

Stepper motor that follows a knob

Beginner50 minGuided buildReviewed

Build it step by step

0 of 4 done
  1. UNO

    Plug in the motor

    The connector only fits one way into the ULN2003 board.

  2. UNO

    Wire the driver

    IN1 to IN4 to D8 to D11. Motor power from the AA pack, ground shared with the Uno.

  3. UNO

    Wire the pot

    Outer pins to 5V and GND, middle to A0.

  4. UNO

    Upload and turn

    Put a paper arrow on the shaft, turn the knob slowly and watch the arrow follow.

In short

How do you build a stepper motor that follows a knob?

A 28BYJ-48 stepper on a ULN2003 board turns to match a potentiometer, with smooth acceleration from the AccelStepper library. You need Arduino Uno R3, 28BYJ-48 Stepper Motor, ULN2003 driver board, Potentiometer 10 kΩ, Battery holder 4 × AA with switch, AA alkaline battery × 4, Breadboard 400 points (half size) and Jumper wires male to female (40 pcs). It takes 4 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Stepper plugULN2003 board socketFive-wire motor connector
ULN2003 IN1 / IN2 / IN3 / IN4Uno D8 / D9 / D10 / D11Coil sequence
ULN2003 + / −4 × AA + / −Motor power (about 240 mA)
4 × AA −Uno GNDShared ground
Pot outer pins / wiperUno 5V and GND / A0Target position

Code

Arduino IDE, board "Arduino Uno". Install "AccelStepper" by Mike McCauley. Note the pin order 8, 10, 9, 11 in the code.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <AccelStepper.h>

// HALF4WIRE with the pin order IN1, IN3, IN2, IN4 suits the 28BYJ-48
AccelStepper motor(AccelStepper::HALF4WIRE, 8, 10, 9, 11);
const long STEPS_PER_TURN = 4096;   // half steps, including the 64:1 gearbox

void setup() {
  motor.setMaxSpeed(800);
  motor.setAcceleration(400);
}

void loop() {
  int raw = analogRead(A0);
  long target = map(raw, 0, 1023, 0, STEPS_PER_TURN);   // knob range = one full turn
  if (abs(target - motor.targetPosition()) > 8) motor.moveTo(target);
  motor.run();
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Knob fully leftShaft at the start position
Knob fully rightShaft one full turn (360°) from the start
Knob to the middleShaft about half a turn (180°)
ULN2003 LEDsFlicker in sequence while it moves

If it does not work

Motor buzzes but does not turn

Wrong pin order. Use 8, 10, 9, 11 as in the code.

Shaft jitters at rest

Raise the dead band (8) to 16 so noise on A0 is ignored.

Very weak

The 28BYJ-48 is a small geared motor. Lower setMaxSpeed to 500 for more torque.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the stepper motor that follows a knob?

Arduino Uno R3, 28BYJ-48 Stepper Motor, ULN2003 driver board, Potentiometer 10 kΩ, Battery holder 4 × AA with switch, AA alkaline battery × 4, Breadboard 400 points (half size) and Jumper wires male to female (40 pcs).

How long does the stepper motor that follows a knob take to build?

About 50 minutes for a beginner maker, in 4 steps.

How do I know the stepper motor that follows a knob works?

Knob fully left: Shaft at the start position. Knob fully right: Shaft one full turn (360°) from the start. Knob to the middle: Shaft about half a turn (180°).

Motor buzzes but does not turn: what should I check?

Wrong pin order. Use 8, 10, 9, 11 as in the code.

Shaft jitters at rest: what should I check?

Raise the dead band (8) to 16 so noise on A0 is ignored.

Very weak: what should I check?

The 28BYJ-48 is a small geared motor. Lower setMaxSpeed to 500 for more torque.