Build it step by step
0 of 8 doneSet up safely
Ventilate, place the iron in its stand and clear flammable things away.
Tin the tip
Melt a little solder onto the clean hot tip.
Practise on scrap
Make five joints on the unused part of the board.
Solder the header and resistors
Fit the low parts first and trim the leads.
Solder the capacitor, LEDs and 555
Check the LED and capacitor polarity first.
Inspect each joint
Look for shiny cone-shaped joints and no bridges.
Fix a bad joint
Use the wick to remove one and resolder it.
Power it
The two LEDs should alternate about once a second.
How do you build a soldering practice board?
Solder resistors, LEDs and headers on perfboard to build a working LED flasher and learn good joints. You need Soldering iron 60 W (adjustable temperature), Soldering stand with sponge, Solder wire 60/40 (0.8 mm, 50 g), Perfboard (dot PCB) 7 × 9 cm, NE555 Timer IC, LED 5 mm red × 2, Resistor 1 kΩ × 2, Resistor 10 kΩ, Resistor 100 kΩ, Electrolytic capacitor 10 µF, 2.54 mm Pin Header, Desoldering wick (braid), 9 V battery and 9 V battery snap with DC jack. It takes 8 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 14
Parts list
- Tools & InstrumentsBuy
- Tools & InstrumentsBuy
- Tools & InstrumentsBuy
- PrototypingBuy
- Integrated CircuitsBuyNE555 Timer IC × 1
- SemiconductorsBuyLED 5 mm red × 2
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuy
- ConnectorsBuy
- Tools & InstrumentsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + via the pin header | 555 pin 8 and pin 4 | Power and reset high |
| 9 V battery - via the pin header | 555 pin 1 | Ground |
| 10 kΩ resistor R1 | 555 pin 8 and pin 7 | Timing resistor |
| 100 kΩ resistor R2 | 555 pin 7 and pin 6 | Timing resistor |
| 555 pins 2 and 6 | Joined | Astable connection |
| 10 µF capacitor | 555 pin 6 and ground, + on pin 6 | Timing capacitor, about 0.7 Hz |
| Red LED A and 1 kΩ resistor | 555 pin 3 through the resistor, LED to ground | On when the output is high |
| Red LED B and 1 kΩ resistor | + rail through the resistor, LED cathode to 555 pin 3 | On when the output is low |
No code needed
No code. Plan to build this on perfboard in this order: header, resistors, then the capacitor, the LEDs and last the 555 on a socket if you have one. A good joint is shiny and shaped like a small cone, with the solder flowing onto both the pad and the lead; a dull ball or a joint that does not wet the pad is a cold joint and should be reflowed. Heat the pad and the lead together for about two seconds and feed the solder to the joint, not to the iron. Work in a ventilated place and use a fume fan if you can, since the flux fumes irritate the lungs, and wash your hands after handling leaded solder. The iron runs at about 350 degrees Celsius, so always return it to the stand and never leave it on unattended; keep children away from it.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Good joint | Shiny, cone-shaped |
| Power on | LEDs alternate |
| Cold joint reflowed | Intermittent faults disappear |
| Wick used on a bridge | Bridge removed cleanly |
If it does not work
Solder will not stick
Clean and tin the tip and heat the pad as well as the lead.
Bridge between pads
Use the wick to remove excess.
Circuit does not run
Check the 555 orientation and the capacitor polarity.
Lifted pad
You held the heat too long; use a wire link to the next point.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the soldering practice board?
Soldering iron 60 W (adjustable temperature), Soldering stand with sponge, Solder wire 60/40 (0.8 mm, 50 g), Perfboard (dot PCB) 7 × 9 cm, NE555 Timer IC, LED 5 mm red × 2, Resistor 1 kΩ × 2, Resistor 10 kΩ, Resistor 100 kΩ, Electrolytic capacitor 10 µF, 2.54 mm Pin Header, Desoldering wick (braid), 9 V battery and 9 V battery snap with DC jack.
How long does the soldering practice board take to build?
About 60 minutes for a beginner maker, in 8 steps.
How do I know the soldering practice board works?
Good joint: Shiny, cone-shaped. Power on: LEDs alternate. Cold joint reflowed: Intermittent faults disappear.
Solder will not stick: what should I check?
Clean and tin the tip and heat the pad as well as the lead.
Bridge between pads: what should I check?
Use the wick to remove excess.
Circuit does not run: what should I check?
Check the 555 orientation and the capacitor polarity.
Lifted pad: what should I check?
You held the heat too long; use a wire link to the next point.
