Design your first PCB in KiCad
Build it step by step
0 of 7 doneDraw the schematic
Parts, references and values.
Run the rules check
Fix every error.
Assign footprints
Through-hole parts.
Lay out the board
Outline and part placement.
Route the traces
0.4 mm wide.
Run the design rules check
Zero errors.
Export the Gerbers
Plot and drill files.
How do you build a design your first PCB in KiCad?
Draw a schematic for a 555 flasher, lay out a small board and export Gerbers for fabrication. You need NE555 Timer IC, LED 5 mm red × 2, Resistor 1 kΩ × 2, Electrolytic capacitor 10 µF, 9 V battery snap with DC jack, Resistor 100 kΩ and Ceramic Capacitor 100 nF. It takes 7 steps and about 180 minutes.
- Level
- Intermediate
- Time
- About 180 min
- Parts
- 7
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- SemiconductorsBuyLED 5 mm red × 2
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuy
- PowerBuy
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| NE555 pins 8 and 4 | Battery plus | Power and reset held high |
| NE555 pin 1 | Battery minus | Ground |
| NE555 pins 2 and 6 joined | 10 µF to ground, and R2 (100 kΩ) to pin 7 | Timing |
| NE555 pin 7 | R1 (1 kΩ) to battery plus | Discharge |
| NE555 pin 3 | LED 1 to ground, and LED 2 to battery plus, each through 1 kΩ | Alternating flash |
| NE555 pin 5 | 100 nF to ground | Control decoupling |
No code needed
This lab has no code. The circuit is a classic 555 flasher: with 1 kΩ, 100 kΩ and 10 µF it flashes about once every 1.4 seconds, and its output swings both ways, so one LED lights while the other is off. In KiCad, draw the schematic first, giving every part a reference such as R1 and a value, then run the electrical rules check; assign footprints (through-hole for your first board is easiest); update the board from the schematic; place parts so the LEDs sit where you want them; set the board outline; route traces at about 0.4 mm wide with 0.3 mm clearance; run the design rule check; and plot Gerber and drill files for a fabrication house. Keep the traces off the board edge and add a ground fill on the back. Check the footprint of each part against the actual part with a printout at 100 percent scale before ordering. Use a 9 V battery only on the finished board. For home etching, only use methods and chemicals with proper protection.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Schematic check | No errors |
| Board check | No design rule errors |
| Paper printout | Real parts sit on the footprints |
| Gerber viewer | Shows all layers and the outline |
If it does not work
Rules check complains
Join each power pin to a power flag.
Footprint wrong
Measure the part and pick the right one.
Traces too close
Raise the clearance or move parts.
Missing drill file
Plot it separately.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the design your first PCB in KiCad?
NE555 Timer IC, LED 5 mm red × 2, Resistor 1 kΩ × 2, Electrolytic capacitor 10 µF, 9 V battery snap with DC jack, Resistor 100 kΩ and Ceramic Capacitor 100 nF.
How long does the design your first PCB in KiCad take to build?
About 180 minutes for a intermediate maker, in 7 steps.
How do I know the design your first PCB in KiCad works?
Schematic check: No errors. Board check: No design rule errors. Paper printout: Real parts sit on the footprints.
Rules check complains: what should I check?
Join each power pin to a power flag.
Footprint wrong: what should I check?
Measure the part and pick the right one.
Traces too close: what should I check?
Raise the clearance or move parts.
Missing drill file: what should I check?
Plot it separately.
