Projects / NFC tag door lock

NFC tag door lock

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Test the reader

    Print a tag number.

  2. ESP32IRLZ44

    Test the lock

    MOSFET and diode.

  3. ESP32

    Choose a master tag

    Copy its number into the sketch.

  4. ESP32

    Add tags

    Master tap, then new tag.

  5. ESP32

    Open with a listed tag

    Lock opens for 5 s.

  6. ESP32

    Remove a tag

    Master tap, then the tag again.

  7. ESP32

    Add a mechanical override

    Key or release.

In short

How do you build an NFC tag door lock?

Tap a phone or tag to open a lock, with a list kept on the device. You need ESP32 DevKit V1, PN532 NFC module, Solenoid lock 12 V, MOSFET IRLZ44N, Rectifier Diode 1N4007, 12 V 2 A DC adapter and Active buzzer 5 V. It takes 7 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
PN532 SDA and SCLESP32 GPIO21 and GPIO22I2C (set the module's switches to I2C)
PN532 VCC and GNDESP32 3V3 and GNDPower
Solenoid lock plus12 V adapter plusLock power
Solenoid lock minusMOSFET drainSwitched side
1N4007 diodeAcross the solenoid, stripe to plusAbsorbs the spike
MOSFET gateESP32 GPIO26Control (add 10 k from gate to GND)
MOSFET source and 12 V adapter minusESP32 GNDCommon ground
Buzzer plus and minusESP32 GPIO27 and GNDBeep
ESP32 VIN5 V from a separate supplyController power

Code

A tag or an NFC phone sends a short number when tapped, and the lock opens if that number is on the list. The list lives in the ESP32's own memory, so it survives a power cut, and a master tag lets you add or remove tags without a computer: tap the master, then the tag. The solenoid is switched by a MOSFET with a diode across it to absorb the spike, and the lock is only on for five seconds so it does not overheat. Be realistic about security: the number on a simple tag is not secret and can be copied, so this suits a cupboard, a workshop drawer or a hobby box, not a door that protects your home. Always keep a mechanical way to open it, since a power cut or a fault must never lock someone in or out of a place they need. Use a fail-secure lock only where that is acceptable, and never on an exit route. Keep the master tag somewhere safe. Arduino IDE with the ESP32 boards package 2.0.x, board "ESP32 Dev Module".

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// NFC tag lock: opens a solenoid lock for 5 seconds when a known tag is tapped. Tap the master tag, then another tag, to add or remove it.
// Libraries: Adafruit PN532, Preferences (built in). Board: ESP32 Dev Module.
// Set MASTER to your master tag's number (the sketch prints every tapped tag over Serial first).
#include <Wire.h>
#include <Adafruit_PN532.h>
#include <Preferences.h>
Adafruit_PN532 nfc(-1, -1);                 // I2C, no IRQ or reset pin
Preferences prefs;
const uint32_t MASTER = 0x00000000;         // replace with the master tag's value from the Serial Monitor
const byte LOCK = 26, BUZZER = 27;
const int MAXTAGS = 10;
uint32_t tags[MAXTAGS]; int nTags = 0;
void loadTags() { prefs.begin("tags", true); nTags = prefs.getInt("n", 0); for (int i = 0; i < nTags; i++) tags[i] = prefs.getUInt(String("t" + String(i)).c_str(), 0); prefs.end(); }
void saveTags() { prefs.begin("tags", false); prefs.putInt("n", nTags); for (int i = 0; i < nTags; i++) prefs.putUInt(String("t" + String(i)).c_str(), tags[i]); prefs.end(); }
int findTag(uint32_t id) { for (int i = 0; i < nTags; i++) if (tags[i] == id) return i; return -1; }
void beep(int ms, int f) { tone(BUZZER, f, ms); delay(ms + 40); }
void openLock() { digitalWrite(LOCK, HIGH); beep(150, 1800); delay(4850); digitalWrite(LOCK, LOW); }
void setup() {
  Serial.begin(115200);
  pinMode(LOCK, OUTPUT); digitalWrite(LOCK, LOW); pinMode(BUZZER, OUTPUT);
  nfc.begin();
  if (!nfc.getFirmwareVersion()) { Serial.println("PN532 not found"); while (true) delay(1000); }
  nfc.SAMConfig();
  loadTags();
}
bool adding = false; unsigned long addUntil = 0;
void loop() {
  uint8_t uid[7]; uint8_t len;
  if (!nfc.readPassiveTargetID(PN532_MIFARE_ISO14443A, uid, &len, 200)) return;
  uint32_t id = 0; for (uint8_t i = 0; i < len && i < 4; i++) id = (id << 8) | uid[i];     // first four bytes
  Serial.print("Tag 0x"); Serial.println(id, HEX);
  if (id == MASTER && MASTER != 0) { adding = true; addUntil = millis() + 10000; beep(100, 1000); beep(100, 1400); }
  else if (adding && millis() < addUntil) {
    int i = findTag(id);
    if (i >= 0) { tags[i] = tags[--nTags]; beep(300, 500); }                    // already known: remove
    else if (nTags < MAXTAGS) { tags[nTags++] = id; beep(100, 2000); }          // new: add
    saveTags(); adding = false;
  }
  else if (findTag(id) >= 0) openLock();
  else beep(400, 300);
  delay(800);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual ESP32 Dev Module with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

PN532 not found

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Listed tagLock opens for 5 s
Unknown tagLow beep, lock stays shut
Master then new tagAdded
Power off and onList is kept

If it does not work

Reader not found

Check the I2C switches and wiring.

Lock does not move

Check the 12 V supply and the diode direction.

Adds the wrong tag

Tap the master first and wait for the double beep.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the NFC tag door lock?

ESP32 DevKit V1, PN532 NFC module, Solenoid lock 12 V, MOSFET IRLZ44N, Rectifier Diode 1N4007, 12 V 2 A DC adapter and Active buzzer 5 V.

How long does the NFC tag door lock take to build?

About 180 minutes for a intermediate maker, in 7 steps.

How do I know the NFC tag door lock works?

Listed tag: Lock opens for 5 s. Unknown tag: Low beep, lock stays shut. Master then new tag: Added.

Reader not found: what should I check?

Check the I2C switches and wiring.

Lock does not move: what should I check?

Check the 12 V supply and the diode direction.

Adds the wrong tag: what should I check?

Tap the master first and wait for the double beep.