Projects / Sapling watering reminder

Sapling watering reminder

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. DIGISPARCAPACITIsoil 67%

    Read raw values first

    Temporarily print or blink out the raw reading in dry and in watered soil to get your two numbers.

  2. DIGISPAR

    Set DRY_LIMIT

    Pick a value between them.

  3. DIGISPAR19.3 mA

    Wire the board

    Power from 2 AA to the 5V pin, sensor power on P1, signal on P2, LED on P0.

  4. DIGISPAR

    Upload

    Plug the Digispark in when the IDE asks. It has a 5 second bootloader wait at power-up.

  5. DIGISPARCAPACITIsoil 67%

    Test

    Leave the sensor in dry soil. After about a minute the LED blinks twice, and keeps doing it each minute.

  6. DIGISPAR

    Water it

    The blinking stops after the next reading.

  7. DIGISPAR++19.3 mA

    Measure sleep current

    Put a multimeter in series with the battery. It should fall to a few hundred microamps or less once the power LED is removed.

In short

How do you build a sapling watering reminder?

A tiny ATtiny85 board with a soil sensor blinks a red LED when a potted sapling is dry and sleeps most of the time so two AA cells last for months. You need Digispark ATtiny85 USB board, Capacitive Soil Moisture Module, LED 5 mm red, Resistor 330 Ω, Battery holder 2 × AA, AA alkaline battery × 2 and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery holder +Digispark 5V pin (bypasses the on-board regulator)3 V from 2 AA cells
Battery holder -Digispark GNDGround
Soil sensor VCCDigispark P1Powered only while reading
Soil sensor GNDDigispark GNDGround
Soil sensor AOUTDigispark P2 (analog input)Moisture signal
Red LED anodeDigispark P0 through 330 ΩReminder
Red LED cathodeDigispark GNDReturn

Code

Arduino IDE with the ATTinyCore or Digistump AVR board package, board "Digispark (Default - 16.5mhz)". Upload with the board's USB when asked. The sensor is read with the ADC reference at the supply, so with 3 V the readings differ from those at 5 V, so read your own values for dry and wet soil and set DRY_LIMIT between them. A Digispark's power LED and regulator waste current, so remove the LED for real months of battery life, and measure the sleep current with a multimeter.

Runs on a virtual Digispark ATtiny85 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <avr/sleep.h>
#include <avr/wdt.h>
#include <avr/interrupt.h>

const byte LED = 0, SENSOR_POWER = 1, SENSOR_IN = A1;     // P0, P1, P2 on the Digispark
const int DRY_LIMIT = 600;                                 // set from your own readings: higher means drier
const byte WAKES_PER_READING = 7;                          // about one reading a minute with 8 s sleeps
volatile byte wakes = 0;

ISR(WDT_vect) { wakes++; }

void sleep8s() {
  MCUSR &= ~_BV(WDRF);
  WDTCR = _BV(WDCE) | _BV(WDE);
  WDTCR = _BV(WDIE) | _BV(WDP3) | _BV(WDP0);               // 8 second interrupt, no reset
  ADCSRA &= ~_BV(ADEN);                                    // turn the ADC off to save power
  set_sleep_mode(SLEEP_MODE_PWR_DOWN);
  sleep_enable();
  sleep_cpu();
  sleep_disable();
  ADCSRA |= _BV(ADEN);
}

void setup() {
  pinMode(LED, OUTPUT);
  pinMode(SENSOR_POWER, OUTPUT);
}

void loop() {
  sleep8s();
  if (wakes >= WAKES_PER_READING) {
    wakes = 0;
    digitalWrite(SENSOR_POWER, HIGH);
    delay(100);                                            // let the sensor settle
    int v = analogRead(SENSOR_IN);
    digitalWrite(SENSOR_POWER, LOW);
    if (v > DRY_LIMIT) {                                   // dry: two short blinks
      for (byte i = 0; i < 2; i++) { digitalWrite(LED, HIGH); delay(80); digitalWrite(LED, LOW); delay(150); }
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Dry soilTwo blinks about once a minute
WateredNo blinks
Sleep currentUnder 0.5 mA after removing the power LED
Battery lifeMonths, from the sleep current and the cell capacity

If it does not work

LED never blinks

DRY_LIMIT is too high or too low for your 3 V readings. Check the numbers.

Sensor corrodes

It must be powered only while reading, as in the code.

Board resets constantly

The supply is too low. Use fresh cells.

Cannot upload

Replug the board after clicking upload. The bootloader waits only a few seconds.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the sapling watering reminder?

Digispark ATtiny85 USB board, Capacitive Soil Moisture Module, LED 5 mm red, Resistor 330 Ω, Battery holder 2 × AA, AA alkaline battery × 2 and Jumper wires male to male (40 pcs, 20 cm).

How long does the sapling watering reminder take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the sapling watering reminder works?

Dry soil: Two blinks about once a minute. Watered: No blinks. Sleep current: Under 0.5 mA after removing the power LED.

LED never blinks: what should I check?

DRY_LIMIT is too high or too low for your 3 V readings. Check the numbers.

Sensor corrodes: what should I check?

It must be powered only while reading, as in the code.

Board resets constantly: what should I check?

The supply is too low. Use fresh cells.

Cannot upload: what should I check?

Replug the board after clicking upload. The bootloader waits only a few seconds.