Projects / Fodder silo level meter

Fodder silo level meter

Intermediate1.3 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire the sensor and screen

    Connect both on the I2C bus as in the table.

  2. NANO

    Check the readings

    Open the Serial Monitor at 115200 and watch the median distance on the display.

  3. NANO

    Mount in the lid

    Point the sensor straight down, away from the walls and the fill pipe.

  4. NANO

    Save empty

    With the bin empty send "e" in the Serial Monitor.

  5. NANO

    Save full

    Fill it, then send "f".

  6. NANO16.3 mA

    Add the low-level LED

    Fit it where it is visible when you walk by.

In short

How do you build a fodder silo level meter?

A VL53L1X laser sensor at the top of a fodder bin shows how full it is, so you reorder before it runs out. You need Arduino Nano, VL53L1X long-range ToF sensor, SSD1306 OLED Display, LED 5 mm red and Resistor 220 Ω. It takes 6 steps and about 75 minutes.

Level
Intermediate
Time
About 75 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
VL53L1X VIN, GNDNano 5V, GNDPower (check your board accepts 5 V on VIN, otherwise use 3V3)
VL53L1X SDA, SCLNano A4, A5I2C
OLED SDA, SCLNano A4, A5I2C, same bus
OLED VCC, GNDNano 5V, GNDPower
Nano D6220 Ω resistor then red LED, to GNDLow-level warning

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "VL53L1X" by Pololu and "U8g2". The EEPROM stores the calibration so it survives power cuts. Keep the sensor window clean of dust. If it sits in a metal lid, set it flush with the inside surface so the beam is not clipped.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <VL53L1X.h>
#include <EEPROM.h>
#include <U8x8lib.h>

VL53L1X sensor;
U8X8_SSD1306_128X64_NONAME_HW_I2C oled(U8X8_PIN_NONE);
const byte LED = 6;
int emptyMM = 1500, fullMM = 200;       // distance when empty and when full, saved in EEPROM
const byte N = 15;

int median() {
  int v[N];
  for (byte i = 0; i < N; i++) { v[i] = sensor.read(); delay(60); }
  for (byte i = 1; i < N; i++) { int k = v[i]; int j = i - 1; while (j >= 0 && v[j] > k) { v[j + 1] = v[j]; j--; } v[j + 1] = k; }
  return v[N / 2];
}

void setup() {
  Serial.begin(115200);
  Wire.begin();
  pinMode(LED, OUTPUT);
  sensor.setTimeout(500);
  sensor.init();
  sensor.setDistanceMode(VL53L1X::Long);
  sensor.setMeasurementTimingBudget(50000);
  sensor.startContinuous(50);
  EEPROM.get(0, emptyMM); EEPROM.get(2, fullMM);
  if (emptyMM < 100 || emptyMM > 4000) { emptyMM = 1500; fullMM = 200; }
  oled.begin();
  oled.setFont(u8x8_font_chroma48medium8_r);
}

void loop() {
  if (Serial.available()) {              // send e with the silo empty, f with it full
    char c = Serial.read();
    if (c == 'e') { emptyMM = median(); EEPROM.put(0, emptyMM); Serial.println("Empty saved"); }
    if (c == 'f') { fullMM = median();  EEPROM.put(2, fullMM);  Serial.println("Full saved"); }
  }
  int d = median();
  int pct = constrain(map(d, emptyMM, fullMM, 0, 100), 0, 100);
  char buf[17];
  snprintf(buf, sizeof buf, "Full %3d %%", pct);
  oled.drawString(0, 1, buf);
  char bar[17]; byte n = pct * 16 / 100;
  for (byte i = 0; i < 16; i++) bar[i] = i < n ? '#' : '.';
  bar[16] = 0;
  oled.drawString(0, 4, bar);
  digitalWrite(LED, pct < 15);           // warn below 15 %
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Empty binAbout 0 %
Half fullAbout 50 %
Full binAbout 100 %
Below 15 %Red LED on

If it does not work

Reads 8190

Nothing in range or the sensor is blinded by dust. Clean and recalibrate.

Reading jumps

The surface is uneven. Aim at the pile centre and use the median.

Percentage backwards

You swapped e and f. Save them again.

Screen blank

Check the I2C address and wiring.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the fodder silo level meter?

Arduino Nano, VL53L1X long-range ToF sensor, SSD1306 OLED Display, LED 5 mm red and Resistor 220 Ω.

How long does the fodder silo level meter take to build?

About 75 minutes for a intermediate maker, in 6 steps.

How do I know the fodder silo level meter works?

Empty bin: About 0 %. Half full: About 50 %. Full bin: About 100 %.

Reads 8190: what should I check?

Nothing in range or the sensor is blinded by dust. Clean and recalibrate.

Reading jumps: what should I check?

The surface is uneven. Aim at the pile centre and use the median.

Percentage backwards: what should I check?

You swapped e and f. Save them again.

Screen blank: what should I check?

Check the I2C address and wiring.