Projects / Queue token display

Queue token display

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANONRF24L01

    Test the radios

    Send a number between the two Nanos.

  2. NANO12:45

    Test the display

    Show 123 on the MAX7219.

  3. NANOSANDIS

    Test the sound

    Play the chime from the SD card.

  4. NANO

    Join them

    Show the number when a packet arrives.

  5. NANO

    Add the buttons

    Next, repeat and the two-button reset.

  6. NANO

    Add the memory

    Save the last number in EEPROM.

  7. NANO

    Install

    Place the display high in the waiting area.

In short

How do you build a queue token display?

A clinic counter presses a button to call the next token number, shown on a big display with a chime. You need Arduino Nano × 2, 8-digit 7-segment module (MAX7219), nRF24L01+ Radio Module × 2, Tactile push button 6 mm × 2, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10), Electrolytic capacitor 10 µF × 2 and Resistor 1 kΩ. It takes 7 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
COUNTER UNIT: nRF24 VCC and GNDNano A 3V3 and GNDPower (add 10 µF across them)
nRF24 CE and CSNNano A D9 and D10Control
nRF24 SCK, MOSI, MISONano A D13, D11, D12SPI
Next buttonNano A D2 and GNDCall next
Repeat buttonNano A D3 and GNDRepeat the number
DISPLAY UNIT: nRF24 VCC and GNDNano B 3V3 and GNDPower (add 10 µF across them)
nRF24 CE and CSNNano B D9 and D10Control
nRF24 SCK, MOSI, MISONano B D13, D11, D12SPI
MAX7219 module DIN, CLK, CSNano B D4, D5, D6Display
MAX7219 VCC and GNDNano B 5V and GNDPower
DFPlayer TXNano B D2Replies
DFPlayer RXNano B D3 through a 1 kΩ resistorCommands
DFPlayer SPK1 and SPK2SpeakerChime and voice

Code

The counter unit sends the token number three times each press, as radio packets can be lost, and the display unit shows it on the large 7-segment module, plays a chime and says the number from the SD card. On the card put the chime as 0001.mp3 in the root and recordings of the numbers in a folder 01 named 001.mp3 to 099.mp3; larger numbers just show and chime. Holding both buttons for 2 seconds resets the count to 0 each morning. The last number is kept in EEPROM so a power cut does not lose it; this writes only when the number changes, which is gentle on the memory. The nRF24 modules run at 3.3 V and need a 10 µF capacitor across their supply or they behave oddly. The radio has no security, so use this only for a convenience display and not for anything that matters for safety. The display unit's 8-digit module can draw a few hundred milliamps at full brightness; power it from a good 5 V adapter. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// COUNTER UNIT (Nano A). Libraries: RF24 (TMRh20). Two buttons: next and repeat. Hold both for 2 seconds to reset to 0.
#include <SPI.h>
#include <RF24.h>
RF24 radio(9, 10);
const byte ADDR[6] = "QUEUE";
int token = 0;
unsigned long both = 0;

void sendToken(bool chime) {
  byte msg[3] = { (byte)(token >> 8), (byte)(token & 255), (byte)chime };
  for (byte i = 0; i < 3; i++) { radio.write(msg, 3); delay(20); }    // send three times in case one is lost
}

void setup() {
  pinMode(2, INPUT_PULLUP); pinMode(3, INPUT_PULLUP);
  radio.begin(); radio.setPALevel(RF24_PA_LOW); radio.openWritingPipe(ADDR); radio.stopListening();
}

void loop() {
  bool next = !digitalRead(2), rep = !digitalRead(3);
  if (next && rep) { if (!both) both = millis(); if (millis() - both > 2000) { token = 0; sendToken(false); both = 0; delay(1000); } return; }
  both = 0;
  if (next) { token++; if (token > 999) token = 0; sendToken(true); delay(600); }
  else if (rep) { sendToken(true); delay(600); }
}

/* ---- DISPLAY UNIT (Nano B). Libraries: RF24, LedControl, DFRobotDFPlayerMini, SoftwareSerial, EEPROM.
#include <SPI.h>
#include <RF24.h>
#include <LedControl.h>
#include <SoftwareSerial.h>
#include <DFRobotDFPlayerMini.h>
#include <EEPROM.h>
RF24 radio(9, 10);
LedControl lc(4, 5, 6, 1);            // DIN, CLK, CS, one module
SoftwareSerial mp3(2, 3);
DFRobotDFPlayerMini player;
const byte ADDR[6] = "QUEUE";
int token = 0, lastSeq = -1;

void show(int n) {
  lc.clearDisplay(0);
  lc.setDigit(0, 0, n % 10, false);
  if (n >= 10) lc.setDigit(0, 1, (n / 10) % 10, false);
  if (n >= 100) lc.setDigit(0, 2, n / 100, false);
}

void setup() {
  lc.shutdown(0, false); lc.setIntensity(0, 12); lc.clearDisplay(0);
  mp3.begin(9600); player.begin(mp3); player.volume(20);
  radio.begin(); radio.setPALevel(RF24_PA_LOW); radio.openReadingPipe(1, ADDR); radio.startListening();
  token = (EEPROM.read(0) << 8) | EEPROM.read(1);          // last number survives a power cut
  if (token > 999) token = 0;
  show(token);
}

void loop() {
  if (radio.available()) {
    byte msg[3]; radio.read(msg, 3);
    int n = (msg[0] << 8) | msg[1];
    if (n != token || msg[2]) {
      bool changed = (n != token);
      token = n; show(token);
      if (changed) { EEPROM.update(0, token >> 8); EEPROM.update(1, token & 255); }
      if (msg[2]) {
        player.play(1);                                      // 0001.mp3 is the chime
        delay(1200);
        if (token > 0 && token < 100) player.playFolder(1, token);   // folder 01, files 001.mp3 to 099.mp3 say the number
      }
    }
  }
}
*/

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press nextNumber goes up, chime, number spoken
Press repeatSame number, chime again
Hold both buttons 2 secondsResets to 0
Power cutDisplay returns to the last number

If it does not work

No packets

Add the 10 µF capacitor and check CE and CSN pins.

Display blank

Check DIN, CLK, CS and the intensity.

No sound

Check the SD card format and the file names.

Misses presses

Move the units closer or raise the radio power level.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the queue token display?

Arduino Nano × 2, 8-digit 7-segment module (MAX7219), nRF24L01+ Radio Module × 2, Tactile push button 6 mm × 2, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10), Electrolytic capacitor 10 µF × 2 and Resistor 1 kΩ.

How long does the queue token display take to build?

About 180 minutes for a intermediate maker, in 7 steps.

How do I know the queue token display works?

Press next: Number goes up, chime, number spoken. Press repeat: Same number, chime again. Hold both buttons 2 seconds: Resets to 0.

No packets: what should I check?

Add the 10 µF capacitor and check CE and CSN pins.

Display blank: what should I check?

Check DIN, CLK, CS and the intensity.

No sound: what should I check?

Check the SD card format and the file names.

Misses presses: what should I check?

Move the units closer or raise the radio power level.