Projects / Posture reminder clip

Posture reminder clip

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Wire the sensor

    I2C to D4 and D5 and power from 3V3.

  2. ESP32BC547

    Build the motor driver

    BC547 base through 1 kΩ to D2, collector to the motor negative, motor positive to 3V3, flyback diode across the motor.

  3. ESP32

    Print the angle

    Upload the code, open the serial monitor and lean forward to check the angle changes. Swap axes in readAngle if not.

  4. ESP32

    Mount the sensor

    Fix it flat on a clip or strip so it sits on your upper back.

  5. ESP32

    Calibrate

    Sit upright and press the button. The motor buzzes once to confirm.

  6. ESP32

    Test

    Slouch for a minute. After 60 seconds it vibrates three times, then waits two minutes before repeating.

  7. ESP32+

    Add the battery

    Connect the LiPo to the XIAO pads and charge it over USB.

In short

How do you build a posture reminder clip?

A clip on your back vibrates when you slouch for more than a minute while sitting. You need Seeed XIAO ESP32C3, MPU6500 6-axis IMU, Vibration motor (coin type), BC547 NPN transistor, Resistor 1 kΩ, Signal Diode 1N4148, Li-Po battery 3.7 V 500 mAh, Tactile push button 6 mm and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
MPU6500 VCC and GNDXIAO 3V3 and GNDSensor supply
MPU6500 SDAXIAO D4I2C data
MPU6500 SCLXIAO D5I2C clock
BC547 baseXIAO D2 through 1 kΩMotor switch
BC547 emitterGNDReturn
BC547 collectorMotor -Low-side switch
Motor +XIAO 3V3Supply
1N4148 across motorCathode on motor +, anode on motor -Flyback protection
Calibrate buttonXIAO D1 and GNDSet your upright position
LiPo batteryXIAO BAT+ and BAT- padsCharges over USB

Code

Arduino IDE with the ESP32 board package by Espressif, board "XIAO_ESP32C3". No libraries, the sensor is read over raw I2C. The angle formula depends on how the board is mounted, so print readAngle() on the serial monitor and swap the axes if the angle does not change as you lean.

Runs on a virtual Seeed XIAO ESP32-C3 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>

const byte MPU = 0x68, MOTOR = D2, BTN = D1;
float upright = 0;                       // angle recorded when the button is pressed
const float LIMIT = 15.0;                // degrees of forward lean that counts as slouching
const unsigned long HOLD_MS = 60000UL;   // lean this long before buzzing
unsigned long leanSince = 0, lastBuzz = 0;
int events = 0;

float readAngle() {
  Wire.beginTransmission(MPU); Wire.write(0x3B); Wire.endTransmission(false);
  Wire.requestFrom(MPU, (uint8_t)6);
  int16_t ax = Wire.read() << 8 | Wire.read();
  int16_t ay = Wire.read() << 8 | Wire.read();
  int16_t az = Wire.read() << 8 | Wire.read();
  return atan2((float)az, (float)ay) * 180.0 / PI;   // forward lean when worn on the back; swap axes if your mounting differs
}

void buzz() { for (byte i = 0; i < 3; i++) { digitalWrite(MOTOR, HIGH); delay(200); digitalWrite(MOTOR, LOW); delay(150); } }

void setup() {
  Serial.begin(115200);
  pinMode(MOTOR, OUTPUT); pinMode(BTN, INPUT_PULLUP);
  Wire.begin();
  Wire.beginTransmission(MPU); Wire.write(0x6B); Wire.write(0); Wire.endTransmission();   // wake the sensor
  delay(100);
  upright = readAngle();
}

void loop() {
  if (digitalRead(BTN) == LOW) { upright = readAngle(); buzz(); delay(500); }
  float lean = readAngle() - upright;
  if (fabs(lean) > LIMIT) {
    if (leanSince == 0) leanSince = millis();
    if (millis() - leanSince > HOLD_MS && millis() - lastBuzz > 120000UL) {
      buzz(); lastBuzz = millis(); events++;
      Serial.print("Slouch events: "); Serial.println(events);
    }
  } else leanSince = 0;
  delay(200);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Sit uprightNo vibration
Lean 20 degrees forward for one minuteThree pulses
Stay slouchedAnother reminder only after two minutes
Press the buttonOne buzz and the upright angle resets

If it does not work

Angle does not change

The axes are wrong for your mounting. Try atan2(ax, az) or atan2(ax, ay).

Motor does not vibrate

Check the BC547 pins and that the motor is on 3V3 and the transistor's collector.

Resets when the motor starts

The coin motor draws a surge. Add a 100 µF capacitor on 3V3.

Battery does not charge

The BAT+ and BAT- pads are swapped. Check polarity.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the posture reminder clip?

Seeed XIAO ESP32C3, MPU6500 6-axis IMU, Vibration motor (coin type), BC547 NPN transistor, Resistor 1 kΩ, Signal Diode 1N4148, Li-Po battery 3.7 V 500 mAh, Tactile push button 6 mm and Jumper wires male to male (40 pcs, 20 cm).

How long does the posture reminder clip take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the posture reminder clip works?

Sit upright: No vibration. Lean 20 degrees forward for one minute: Three pulses. Stay slouched: Another reminder only after two minutes.

Angle does not change: what should I check?

The axes are wrong for your mounting. Try atan2(ax, az) or atan2(ax, ay).

Motor does not vibrate: what should I check?

Check the BC547 pins and that the motor is on 3V3 and the transistor's collector.

Resets when the motor starts: what should I check?

The coin motor draws a surge. Add a 100 µF capacitor on 3V3.

Battery does not charge: what should I check?

The BAT+ and BAT- pads are swapped. Check polarity.