Projects / Gym rep counter

Gym rep counter

Intermediate4 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32LSM6DS3tilt 43°

    Test the IMU

    Print the acceleration while you move.

  2. ESP32

    Plot a rep

    See the up and down shape in the serial plotter.

  3. ESP32LSM6DS3tilt 43°

    Count with hysteresis

    Two thresholds and a minimum time.

  4. ESP32

    Add the set buzz

    Buzz after 10 reps.

  5. ESP32

    Add BLE

    Notify the counts to a scanner app.

  6. ESP32

    Build the strap

    Fit the board snugly on the wrist.

  7. ESP32

    Tune

    Adjust the thresholds for each exercise.

In short

How do you build a gym rep counter?

An IMU on your wrist counts reps of curls, presses and squats and shows sets on your phone. You need Seeed XIAO ESP32S3, LSM6DS3 6-axis IMU, Li-Po battery 3.7 V 500 mAh, Vibration motor (coin type), BC547 NPN transistor, Resistor 1 kΩ and Signal Diode 1N4148. It takes 7 steps and about 240 minutes.

Level
Intermediate
Time
About 240 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
IMU VCC and GNDXIAO 3V3 and GNDPower
IMU SDAXIAO D4I2C data
IMU SCLXIAO D5I2C clock
XIAO D21 kΩ to BC547 baseMotor switch
BC547 collectorMotor minusSwitched return
BC547 emitterXIAO GNDGround
Motor plusXIAO 3V3Supply
1N4148Across the motor, stripe to 3V3Flyback protection
LiPoXIAO BAT padsPower and charging

Code

Every rep of a curl or press makes a rise and fall in the acceleration on the wrist. The sketch subtracts a slow baseline so gravity and posture do not matter, then counts a rep each time the movement rises above an upper threshold and has fallen below a lower one since the last rep; that gap is called hysteresis and stops one rep from counting twice. A minimum of 0.7 seconds between reps ignores jitter. Record a few reps of each exercise on the serial plotter and adjust the two thresholds to suit; a slow squat has a smaller swing than a fast curl. A short buzz marks the end of a set and a BLE scanner app can read the counts. This is a training aid and not a medical device; use proper form and a sensible weight, and stop if you feel pain. Wear it on a snug strap, not a tight one, and use a protected LiPo in a sewn pocket; never train with it while charging. Arduino IDE with the ESP32 boards package, board "XIAO_ESP32S3".

Runs on a virtual Seeed XIAO ESP32-S3 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Rep counter with BLE. Libraries: Adafruit LSM6DS, ESP32 BLE Arduino (built in). Board: XIAO ESP32S3.
// Change the class if your chip differs: Adafruit_LSM6DS3, Adafruit_LSM6DS3TRC or Adafruit_LSM6DS33.
#include <Wire.h>
#include <Adafruit_LSM6DS3.h>
#include <BLEDevice.h>
#include <BLEServer.h>
#include <BLEUtils.h>
#include <BLE2902.h>

#define SERVICE_UUID "6e400011-b5a3-f393-e0a9-e50e24dcca9e"     // example UUIDs, make your own for real projects
#define COUNT_UUID   "6e400012-b5a3-f393-e0a9-e50e24dcca9e"     // notify: reps and sets as two bytes
Adafruit_LSM6DS3 imu;
BLECharacteristic* countChar;
bool connected = false;
const int MOTOR = D2;
const int REPS_PER_SET = 10;
int reps = 0, sets = 0;
float filtered = 0, level = 0;                       // smoothed movement and its slow average
bool above = false; unsigned long lastRep = 0;

class Cb : public BLEServerCallbacks {
  void onConnect(BLEServer*) { connected = true; }
  void onDisconnect(BLEServer* s) { connected = false; s->startAdvertising(); }
};

void buzz(int ms) { digitalWrite(MOTOR, HIGH); delay(ms); digitalWrite(MOTOR, LOW); }

void setup() {
  pinMode(MOTOR, OUTPUT);
  Wire.begin();
  imu.begin_I2C();
  BLEDevice::init("ElectroLark-Reps");
  BLEServer* srv = BLEDevice::createServer(); srv->setCallbacks(new Cb());
  BLEService* svc = srv->createService(SERVICE_UUID);
  countChar = svc->createCharacteristic(COUNT_UUID, BLECharacteristic::PROPERTY_NOTIFY | BLECharacteristic::PROPERTY_READ);
  countChar->addDescriptor(new BLE2902());
  svc->start();
  BLEDevice::getAdvertising()->addServiceUUID(SERVICE_UUID);
  BLEDevice::getAdvertising()->start();
}

void loop() {
  sensors_event_t a, g, t; imu.getEvent(&a, &g, &t);
  float mag = sqrt(a.acceleration.x * a.acceleration.x + a.acceleration.y * a.acceleration.y + a.acceleration.z * a.acceleration.z);
  filtered += (mag - filtered) * 0.2;                // smooth quick jitter
  level += (filtered - level) * 0.01;                // slow baseline (gravity and posture)
  float swing = filtered - level;                    // movement above or below the baseline
  // hysteresis: count when the swing rises above the upper threshold, re-arm only after it falls below the lower one
  if (!above && swing > 2.0 && millis() - lastRep > 700) {      // 2.0 m/s^2 up, at least 0.7 s between reps
    above = true; lastRep = millis(); reps++;
    if (reps >= REPS_PER_SET) { reps = 0; sets++; buzz(300); }   // buzz at the end of each set
    uint8_t d[2] = { (uint8_t)reps, (uint8_t)sets };
    countChar->setValue(d, 2); if (connected) countChar->notify();
  }
  if (above && swing < 0.8) above = false;
  delay(10);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Do 10 slow curlsCounts 10, buzzes once
Shake the wrist lightlyDoes not count
RestCount stays still
Phone scannerShows reps and sets update

If it does not work

Counts twice per rep

Raise the lower threshold or lengthen the minimum time.

Misses slow reps

Lower the upper threshold.

No BLE

Check the board package and Bluetooth is on.

Motor always on

Check the transistor pins and the base resistor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the gym rep counter?

Seeed XIAO ESP32S3, LSM6DS3 6-axis IMU, Li-Po battery 3.7 V 500 mAh, Vibration motor (coin type), BC547 NPN transistor, Resistor 1 kΩ and Signal Diode 1N4148.

How long does the gym rep counter take to build?

About 240 minutes for a intermediate maker, in 7 steps.

How do I know the gym rep counter works?

Do 10 slow curls: Counts 10, buzzes once. Shake the wrist lightly: Does not count. Rest: Count stays still.

Counts twice per rep: what should I check?

Raise the lower threshold or lengthen the minimum time.

Misses slow reps: what should I check?

Lower the upper threshold.

No BLE: what should I check?

Check the board package and Bluetooth is on.

Motor always on: what should I check?

Check the transistor pins and the base resistor.